Prelubrication Pump Problem
使用本程序诊断和排除预润滑压力低故障,或者在以下事件代码为激活状态时使用本程序。 关于事件代码的信息,请参阅故障诊断与排除, "事件代码"。 必须进入 Caterpillar 电子技师(ET)上的发动机监控系统才能查看这些代码的当前触发点。 关于发动机监控系统的信息,请参阅故障诊断与排除, "发动机监控系统"。
Show/hide table
事件代码 | ||
---|---|---|
说明 | 激活代码的条件 | 系统响应 |
E233(1) 发动机预润滑压力低 | 预润滑压力不超过编程延迟时间的触发点。 | 记录该代码。
防止发动机起动。 |
- 供气压力
- 预润滑泵润滑器
- 预润滑泵空气马达的排气出口管
- 发动机机油供给
- 泵控制电磁阀
- 预润滑压力开关
- 预润滑泵
检查并确认预润滑泵控制电磁阀上的供气压力充足。 电磁阀接合时检查预润滑泵上的供气压力。 确保空气压力足以运行泵。 检查系统是否泄漏和/或堵塞。
检查并确认预润滑泵润滑器充分装满正确的润滑剂。
检查并确认润滑器在预润滑周期中正常工作。
检查并确认预润滑泵空气马达的排气出口管未阻塞。
检查发动机机油油位。 保持机油油位在油尺的 "ADD"(加注)和 "FULL"(满)标记之间。 检查润滑系统有无泄漏。
如果发动机机油供给正确,查找预润滑泵的油管有无泄漏。 确保发动机机油供给没有阻塞。 根据需要进行修理。
确保泵控制电磁阀的输出由电子控制模块(ECM)激活。 检查有无与电磁阀相关的诊断代码。 请参考故障诊断与排除, "预润滑 - 测试",以了解与电磁阀电路故障诊断与排除相关的信息。
预润滑泵压力开关必须在 ECM 起动发动机前关闭。 关闭前,开关必须检测到发动机机油油道内
预润滑泵可能有机械故障。 检查预润滑泵。 请参考发动机拆解和组装以了解详情。
Caterpillar Information System:
C9 Petroleum Engines Engine Oil Pan - Remove and Install
C175 Generator Sets After Starting Engine
C9 Petroleum Engines Cylinder Head - Install
Caterpillar Machine Fluids Recommendations Distillate Diesel Fuel
G3600 Engines Prelubrication - Test
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Display of Voltage or Current or Power Is Inaccurate
C9 Petroleum Engines Cylinder Head - Remove
2007/12/03 Improved Wiring for the Speed Control for the Electronic Governor {1408, 1417}
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Troubleshooting Diagnostic Codes
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224} Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}
C9 Petroleum Engines Rocker Arm and Shaft - Install
320D and 323D Excavators Hydraulic System Swing Drive
G3600 Engines Air Starting Motor Problem
G3600 Engines Starting - Test
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Indicators of Alarm Module or Remote Annunciator Are Constantly Flashing
C175 Generator Sets Fuel Related Components in Cold Weather
2008/01/07 A New O-ring for the Injector Sleeve is Now Used {1100}
2008/01/01 A New O-ring for the Injector Sleeve is Now Used {1100}
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0111 - FMI 03
2011/02/11 Procedure to Use the Correct Mounting Bolts with the 10R-2356 Flywheel As {1156}
2007/12/24 Procedure to Use the Correct Mounting Bolts with the 10R-2356 Flywheel As {1156}
2007/12/01 Procedure to Use the Correct Mounting Bolts with the 10R-2356 Flywheel As {1156}
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0190 - FMI 02
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Hydraulic Control - Remove