Crankcase Breather - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| |
| Illustration 1 | g01435395 |
- Remove bolt (2) and the washer from breather assembly (1).
- Loosen hose clamp (3) and hose clamp (5). Remove hose assembly (4).
- Remove breather assembly (1) and the O-ring seal.
- Remove the bolts and fumes disposal group (6), if necessary.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install fumes disposal group (6) and the bolts, if necessary.
- Check the condition of the O-ring seal. Replace the O-ring seal if the O-ring seal is damaged.
- Install the O-ring seal and breather assembly (1).
- Install bolt (2) and the washer. Tighten bolt (2) to a torque of
15 ± 3 N·m (11 ± 2 lb ft) . - Install hose assembly (4). Tighten hose clamp (5) and hose clamp (3).
Show/hide table
|
| |
| Illustration 2 | g01435395 |
Caterpillar Information System:
C27 and C32 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Install
C4.4 Generator Set Engines Injector Solenoid Circuit - Test
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Assemble
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Disassemble
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Install
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Remove
C9 Petroleum Engines Housing (Front) - Install
C15 and C18 Petroleum Generator Sets Speed Sensor - Clean/Inspect
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission and Torque Converter - Connect
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission and Torque Converter - Separate
C9 Petroleum Engines Housing (Front) - Remove
2007/12/03 Improved PL1000T Hardware and Software is Now Available {7610}
G3600 Engines Sensor Signal (PWM) - Test
C9 Petroleum Engines Cylinder Block Cover - Remove and Install
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Fasteners
G3600 Engines Fuel Control - Test
320D and 323D Excavators Hydraulic System Swing Drive
C9 Petroleum Engines Rocker Arm and Shaft - Install
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224} Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Troubleshooting Diagnostic Codes
2007/12/03 Improved Wiring for the Speed Control for the Electronic Governor {1408, 1417}
C9 Petroleum Engines Cylinder Head - Remove
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Display of Voltage or Current or Power Is Inaccurate
G3600 Engines Prelubrication - Test