Torque Converter - Install
安装步骤
Show/hide table
需要的工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
B     | 1U-9200     | 杠杆式拔拉起重机     | 1     |
C     | 1P-2420     | 变速箱修复台     | 2     |
- 稍微升起变矩器 (1) ,然后拆下分动器 (4) 。
Show/hide table
图 1 | g01447727 |
Show/hide table
图 2 | g01447725 |
- 拆下变矩器 (1) 。 变矩器 (1) 的重量约为 532 kg (1173 lb)。 将变矩器 (1) 放置在工具 (B) (未显示)上。
- 拆下螺栓 (3) 。
Show/hide table
图 3 | g01447723 |
- 拆下螺栓 (2) 。
Show/hide table
图 4 | g01447720 |
- 将工具 (A) 装在变矩器组件 (1) 上。
Show/hide table
图 5 | g01447719 |
- 将工具 (A) 和适当的起吊设备装在变矩器组件 (2) 上。 将工具 (B) 装在变矩器组件 (2) 上。 变矩器组件 (2) 的重量约为 1108 kg (2440 lb)。
Show/hide table
图 6 | g01435372 |
Show/hide table
图 7 | g01435343 |
- 从工具 (C) 上拆下变矩器组件 (1) 。
- 旋转变矩器组件 (2) ,然后将变矩器组件 (2) 放在地面上。
- 拆下工具 (A) 、工具 (B) 和适当的起吊设备。
End By: 连接变矩器。 请参阅 拆解和组装, "变速箱和变矩器 - 连接"。
Caterpillar Information System:
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Remove
C9 Petroleum Engines Housing (Front) - Install
C15 and C18 Petroleum Generator Sets Speed Sensor - Clean/Inspect
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission and Torque Converter - Connect
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission and Torque Converter - Separate
C9 Petroleum Engines Housing (Front) - Remove
2007/12/03 Improved PL1000T Hardware and Software is Now Available {7610}
C3.3 Industrial Engine Model View Illustrations
C4.4 Generator Set Engines Injector Data Incorrect - Test
G3520B Industrial Engines Diagnostic Trouble Codes
G3520B Industrial Engines Event Codes
3176C, 3406E and 3456 Industrial Engines ECM Does Not Communicate with Other Modules
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Disassemble
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Assemble
C4.4 Generator Set Engines Injector Solenoid Circuit - Test
C27 and C32 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Install
C9 Petroleum Engines Crankcase Breather - Remove and Install
G3600 Engines Sensor Signal (PWM) - Test
C9 Petroleum Engines Cylinder Block Cover - Remove and Install
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Fasteners
G3600 Engines Fuel Control - Test
320D and 323D Excavators Hydraulic System Swing Drive
C9 Petroleum Engines Rocker Arm and Shaft - Install
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224} Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}