Fuel Injector - Remove and Install
开始:
- 拆下燃油喷油管。 请参阅拆解和组装, "燃油喷油管路 - 拆卸和安装"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 用一个深孔套筒从缸盖上拆下喷油器 (1)。
- 将座圈 (2) 从缸盖上拆下。
- 立刻盖上所有开口或者将其塞住。
Show/hide table
图 1 | g01320610 |
典型示例 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 239-3312 | 密封胶 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 清洁缸盖内喷油器的孔。 确保没有碎屑进入气缸。 清洁喷油器体上的螺纹。
- 将新的座圈 (2) 安装到缸盖上的喷油器孔中。
- 在接合到缸盖上的头两道喷油器螺纹上涂抹一滴工具 (A)。 这一滴工具的直径为
2 mm (0.08 inch) ,长度为6 mm (0.25 inch) 。注: 确保工具 (A) 未遮住螺纹下方的喷油器体。
- 将喷油器 (1) 安装到缸盖中。 用深孔套筒将喷油器拧紧至扭矩
64 N·m (47 lb ft) 。
Show/hide table
图 2 | g01304054 |
典型示例 |
结束:
- 安装喷油管。 请参阅拆解和组装, "燃油喷油管路 - 拆卸和安装"。
Caterpillar Information System:
C4.4 Industrial Engine Refill Capacities and Recommendations
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3176C, 3406E and 3456 Industrial Engines Sensor Signal (Analog, Active) - Test
C4.4 Industrial Engine Maintenance Interval Schedule
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
14L Motor Grader Machine Systems Circle Drive - Install
312D2 and 313D2 Excavators Machine Systems Storage Box and Covers (Cab) - Remove and Install
2008/01/01 Improved Routing of the Injector Wiring Harness {1290, 1408}
Reuse and Salvage for Camshafts {1210, 1210} Reuse and Salvage for Camshafts {1210, 1210}
G3520B Industrial Engines Prelubrication - Test
C32 Marine Auxiliary Engine Configuration Parameters
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
785D OEM Off-Highway Truck Suspension Cylinder Pressure Sensor (Front Suspension Cylinder)
3406E and C15 Marine Engines Auxiliary Water Pump