Circle Drive - Install
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 138-7575 | 连杆支架 | 3 |
| B | 169-0503 | 安装套件 | 1 |
| 1U-8849 | Duo-Cone 密封件安装器组件 | 1 | |
注: 清洁度是一项重要的因素。 组装之前，应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上，从而在将来引发故障。 检查所有零件。 如果任何零件磨损或损坏，则应使用新零件进行更换。
- 使用工具 (B) 将 Duo-Cone 密封件 (12) 安装进齿轮 (9) 中。 请参阅拆解和组装, "Duo-Cone 通用浮式密封 - 安装"。
Show/hide table
 | |
| 图 1 | g00929332 |
- 使用工具 (B) 将 Duo-Cone 密封件 (11) 安装进转盘驱动 (8) 中。
Show/hide table
 | |
| 图 2 | g00929328 |
- 将工具 (A) 连接至转盘驱动 (8) 上。 将适当的起吊设备连接到工具 (A) 上。 转盘驱动 (8) 的重量约为 127 kg (280 lb)。
Show/hide table
 | |
| 图 3 | g00929325 |
- 安装齿轮 (9) 和止推垫圈 (10) 。 当将转圈驱动 (8) 降低到位时。
- 拆下工具 (A) 。
Show/hide table
 | |
| 图 4 | g00929323 |
- 安装三个螺栓 (7) 。
- 安装螺栓 (6) 。
- 安装螺母 (5) 。 拧紧螺母 (5) 至扭矩 530 ± 70 N·m (391 ± 52 lb ft)。 安装 O 形密封圈 (4) 。
Show/hide table
 | |
| 图 5 | g00929322 |
- 安装垫圈 (3) 、锁 (1) 和螺母 (2) 。 弯曲螺母 (2) 上的锁 (1) 。 拧紧螺母 (2) 至扭矩 325 ± 27 N·m (240 ± 20 lb ft)。
End By: 分离转向机架锁。 请参阅 拆解和组装, "转盘驱动 - 拆卸"。
Caterpillar Information System:
312D2 and 313D2 Excavators Machine Systems Storage Box and Covers (Cab) - Remove and Install
2008/01/01 Improved Routing of the Injector Wiring Harness {1290, 1408}
Reuse and Salvage for Camshafts {1210, 1210} Reuse and Salvage for Camshafts {1210, 1210}
G3520B Industrial Engines Prelubrication - Test
C32 Marine Auxiliary Engine Configuration Parameters
G3600 Engines Event Codes
G3600 Engines Diagnostic Trouble Codes
C11 and C13 Petroleum Engines Speed Sensor - Clean/Inspect
C32 Marine Auxiliary Engine Monitoring System
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module Speed Control (Switch) - Test
3176C, 3406E and 3456 Industrial Engines Sensor Supply - Test
C4.4 Industrial Engine Belt Tensioner - Inspect
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C4.4 Industrial Engine Maintenance Interval Schedule
3176C, 3406E and 3456 Industrial Engines Sensor Signal (Analog, Active) - Test
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove and Install
C4.4 Industrial Engine Refill Capacities and Recommendations
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injector - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Install