3608 Engine Caterpillar


Air Inlet Shutoff - Remove and Install

Usage:

3608 1ZD

Removal Procedure


    NOTICE

    Keep all parts clean from contaminants.

    Contaminants may cause rapid wear and shortened component life.


    ------ WARNING! ------

    Personal injury or death can occur from not following the proper procedure or the recommended tooling.

    To prevent the possibility of injury or death, follow the established procedure using the recommended tooling.

    ----------------------

    ------ WARNING! ------

    Before you remove the air intake shutoff, pull the trip knob on the air intake shutoff or press the emergency stop button in order to release the blade latch. If the blade latch is released after the air intake shutoff is removed, serious personal injury can result.

    ----------------------

    Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.

  1. Pull the emergency knob on the air intake shutoff or press the emergency stop button in order to release the blade latch on the air inlet shutoff.



    Illustration 1g01287971

  1. Remove hose assembly (2) from air inlet shutoff (3) .

  1. Remove bolts (4), bolts (6), and elbow (5) .

  1. Remove bolts (1). Remove air inlet shutoff (3). Check the gaskets and replace the gaskets, if necessary.

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


    Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.




    Illustration 2g01287971

  1. Clean all mating surfaces and install the gaskets and air inlet shutoff (3). Install bolts (1) .

  1. Install elbow (5), bolts (4), and bolts (6) .

  1. Install hose assembly (2) on air inlet shutoff (3) .

  1. Reset the air inlet shutoff to the "OPEN" position.

Caterpillar Information System:

3608 Engine Fuel Transfer Pump - Install
3608 Engine Fuel Priming Pump - Assemble
3608 Engine Fuel Priming Pump - Disassemble
C15 and C18 Petrolem Generator Set Engines Sensor Signal (Analog, Active) - Test
3608 Engine Fuel Injector - Install
3608 Engine Fuel Injector - Remove
3608 Engine Governor Drive - Assemble - Later
Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 1, 2, and 3) {5061, 5073} Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 1, 2, and 3) {5061, 5073}
3176C and 3196 Engines for Caterpillar Built Machines Belt Tensioner
3500B and 3500C Marine Propulsion Engines Engine Will Not Crank
3608 Engine Governor - Install
3608 Engine Governor - Remove
C15 and C18 Petrolem Generator Set Engines Sensor Signal (Analog, Passive) - Test
3608 Engine Exhaust Manifold - Remove and Install
Procedure to Update a Standard TH48-E80 Oil/Gas Transmission to a Warm-Up Mode TH48-E80 Oil/Gas Transmission{1408, 3083, 3160, 3168, 4800, 7610} Procedure to Update a Standard TH48-E80 Oil/Gas Transmission to a Warm-Up Mode TH48-E80 Oil/Gas Transmission{1408, 3083, 3160, 3168, 4800, 7610}
3608 Engine Turbocharger - Remove
3608 Engine Turbocharger - Disassemble
3608 Engine Turbocharger - Assemble
3608 Engine Turbocharger - Install
C175-16 and C175-20 Generator Set Engines Cylinder Head
14L Motor Grader Machine Systems Circle - Remove
3176C and 3196 Engines for Caterpillar Built Machines Engine Support (Front)
2007/12/24 An Improved Exhaust Bellow is Used {1059}
3608 Engine Prelubrication Oil Pump - Disassemble
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.