- Asphalt Paver:
- AP-600 (S/N: B2S)
Introduction
Illustration 1 | g01051135 |
The supplemental product support literature should be used with the appropriate Service Manual and the appropriate Parts Manual that is available for each standard machine. This supplement is used to determine the difference between the custom modifications and a standard machine.
The Service Manual and the Parts Manual that is available for the standard machine should be used if the service information is not in this supplementary product support literature.
Usage of German Road Homologation Kit
Procedure to Engage the Locking Pins for the Front Wheels
Note: Perform the following procedure in order to evenly distribute the weight of the paver and screed. This weight distribution enables the machine to travel on the road. This procedure should be performed in order to drive the machine from one job site to another job site.
- Fully raise the screed to the TRAVEL position and engage the lock bars (1). Refer to Operation and Maintenance, "Screed Travel Lock" for the correct procedure.
Illustration 2 | g01411827 |
(1) Lock bars |
- Fully raise the hopper and engage lock pins (2) for the hopper. Refer to Operation and Maintenance, "Hopper Travel Lock" for the correct procedure.
Illustration 3 | g01411834 |
(2) Lock pins |
- Move the machine to a flat, level surface.
- Move propel lever (3) to the NEUTRAL position.
Illustration 4 | g01411859 |
(3) Propel lever (4) Operating mode selector |
- Move operating mode selector (4) to the STANDBY position.
- Depress parking brake control (5) in order to engage the parking brake.
Illustration 5 | g01411874 |
(5) Parking brake control (6) Speed control knob |
- Press speed control knob (6) in order to reduce the engine speed to MINIMUM.
- Ramps (7) are provided with the machine.
Illustration 6 | g01411912 |
(7) Ramps |
- Position ramps (7) in front of the front wheels on both sides of the machine.
- Move the selector for propel speed (8) to the SLOW position.
Illustration 7 | g01411939 |
(4) Operating mode selector (8) Selector for propel speed |
- Disengage the parking brake.
- Move operating mode selector (4) to the MANUAL position.
- Use propel lever (3) to slowly move the machine forward until the front two wheels are fully on the flat surface of ramps (7) .
Illustration 8 | g01420546 |
(3) Propel lever |
Illustration 9 | g01411949 |
(7) Ramps |
- Move propel lever (3) to the NEUTRAL position and engage the parking brake.
Illustration 10 | g01411955 |
(3) Propel lever (4) Operating mode selector |
- Move operating mode selector (4) to the STANDBY position.
- Loosen locking knob (9) and move locking pins (10) for the front wheels to the internal side of the machine.
Illustration 11 | g01412064 |
This photo shows the locking pin, in the unlocked position. This photo shows the front wheels on the left side of the machine. (9) Locking knob (10) Locking pins |
Illustration 12 | g01420499 |
This photo shows the locking pin, in the locked position. This photo shows the front wheels on the left side of the machine. (9) Locking knob (10) Locking pins |
- Tighten locking knob (9) in order to lock front wheels locking pins in position.
- Pull parking brake control (5) in order to disengage the parking brake for the machine.
Illustration 13 | g01412086 |
(5) Parking brake control |
- Move operating mode selector (4) to the MANUAL position.
Illustration 14 | g01411955 |
(3) Propel lever (4) Operating mode selector |
- Slowly move propel lever (3) to REVERSE. Slowly lower the machine from the ramps to the ground.
- Reverse this procedure in order to lower the front wheels to the working position.
NOTICE |
---|
When traveling on public roads use slow speed in order to avoid damage to the front wheel bearings. |
NOTICE |
---|
Lower the front wheels to the working position before paving. |