Engine Shutdown Is Intermittent
注: 只有在操作过程中发动机完全停机的情况下才使用本步骤。
可能原因
- 诊断代码
- 事件代码
- 电气接头
- 开关
- 断路器
- 燃油供给
建议的措施
诊断代码和 / 或事件代码
某些诊断代码和 / 或事件代码可能会造成发动机停机。 连接 Caterpillar 电子维修技师(ET)并检查是否存在激活的代码和记录的代码。 在继续进行本步骤之前应对出现的任何代码进行故障诊断与排除。
电气接头
- 检查电子控制模块(ECM)J1/P1 和 J2/P2 接头是否正确安装。 此外,还应彻底检查发动机转速 / 正时传感器接头。 请参考故障诊断与排除, "电气接头 - 检查"。
- 对从 ECM 到蓄电池室的蓄电池导线进行检查。 请参阅示意图以了解特定的接线信息。 检查至 ECM 的钥匙开关输入。 检查单体喷油器接头及相关导线有无损坏或有无间歇性故障。 检查所有发动机电路保护装置的导线和接头。 检查ECM的电源和接地线路的连接情况。 检查发动机停机开关及相关导线。 请参阅故障诊断与排除, "供电电源 - 测试"。
开关
检查发动机停机开关及相关导线。 另外,如果应用场合中配有超速确认开关,则检查此开关是否正常工作。
断路器
检查全部相关断路器的状态。 如果断路器跳闸,复位断路器。 使发动机重新投入使用之前应确定造成电路断路器跳闸的条件。 进行必要的修理。
燃油供给
- 目视检查燃油箱中的油位。 不可全信燃油表。 如有必要,向燃油箱添加燃油。 如果发动机用尽燃油,则需要充注燃油系统。 请参考操作和保养手册。
- 检查燃油管路有无以下故障:阻塞, 皱缩管路 和 挤压管路。 如果发现燃油管路有故障,则应修理和/或更换管路。
- 检查燃油箱有无可能会堵塞燃油供应的异物或碎屑。
- 如果进行以下任何步骤,则应充注燃油系统:
- 更换燃油滤清器
- 维护燃油低压供油回路
- 更换单体喷油器
注: 检查燃油系统是否混入空气。 请参考系统操作/测试和调整手册。
- 更换燃油滤清器
Show/hide table
注意 |
---|
持续盘车不要超过30秒。 再次盘车前,让起动马达先冷却2分钟。 |
- 检查燃油质量。 低温天气会对燃油特性带来不利影响。 请参考操作和保养手册。
- 检查发动机盘车起动时过滤后燃油的压力。 请参考系统操作/测试和调整。
如果燃油压力偏低,更换燃油滤清器。 清理粗滤器 / 水分离器的碎屑。 请参考操作和保养手册。
如果燃油压力仍然过低,则应检查燃油压力调节阀的工作情况。 此外,还应检查输油泵是否正常工作。 请参考系统操作/测试和调整。
Caterpillar Information System:
349F and 352F Excavators Pump Coupling Oil Level - Check
3176C, 3406E and 3456 Industrial Engines Engine Cranks but Does Not Start
Cat® Digital Voltage Regulator Generator Overcurrent - Troubleshoot
3176C Engine for Caterpillar Built Machines Electronic Service Tool Does Not Communicate
345D, 349D and 349D2 Excavators Pump Coupling Oil - Change
2008/02/01 Repairing the Fuel Injector Rocker Arm {1102, 1123, 1290}
2007/08/01 Precautions for Cylinder Liner Installation {1201, 1216}
2007/08/27 Precautions for Cylinder Liner Installation {1201, 1216}
G3408C and G3412C Engines Valve Cover
Reuse and Salvage for Turbochargers {0760, 0767, 1052} Reuse and Salvage for Turbochargers {0760, 0767, 1052}
2007/08/01 Updated Procedure for Cleaning the Nozzles in the Aftertreatment Regeneration Device (ARD) {1719, 1722}
C4.4 (Mech) Industrial Engine Fuel System Pressure - Test
C15 and C18 Petroleum Engines Alternator and Regulator
3512, 3508 and 3516 Generator Sets Engine Oil and Filter - Change
2007/08/27 New AccuGrade ® Software is Now Available {7220, 7620}
Multiple Registration Messages Occur with Product Link{733T, 7606} Multiple Registration Messages Occur with Product Link{733T, 7606}
Parts Stock Cylinder Head Assemblies with Rust Preventative Applied{1100} Parts Stock Cylinder Head Assemblies with Rust Preventative Applied{1100}
2007/09/10 A New Socket for the Rocker Arm Provides Increased Lubrication for Low Load Operation {1102, 1123}
3500 Generator Sets Fuel System Secondary Filter - Replace
2007/10/08 New ECM Software Is Available for Gas Compression Applications {7620}
2007/09/01 An Improved Oil Level Gauge Is Now Used {1326}
The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290} The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290}
Correct Usage of the Oil Rail Plug for the Cylinder Head on C9 Engines{1100} Correct Usage of the Oil Rail Plug for the Cylinder Head on C9 Engines{1100}
C3.3 Industrial Engine Fan Drive