Cab - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7574     | 连杆支架     | 3     |
B     | 9S-3263     | 螺纹锁固胶     | 1     |
- 将工具 (A) 和适当的起吊设备连接到驾驶室 (24) 。 驾驶室 (24) 的重量约为 726 kg (1600 lb)。
Show/hide table
图 1 | g01404682 |
Show/hide table
图 2 | g01404683 |
- 安置驾驶室 (24) 。 在螺栓 (25) 上使用工具 (B) 并安装螺栓 (25) 。 拧紧螺栓 (25) 至扭矩为 850 ± 100 N·m (627 ± 74 lb ft)。 拆下工具 (A) 和任何适当的起吊设备。
- 重新安置挡板 (23) ,并安装新电缆带 (22) 。
Show/hide table
图 3 | g01404790 |
- 连接接地电缆 (21) 。
Show/hide table
图 4 | g01404793 |
- 连接线束组件 (20) 。
Show/hide table
图 5 | g01404681 |
- 连接线束组件 (19) 后将螺栓 (18) 上紧到 2.25 ± 25 N·m (20.0 ± 2.2 lb in) 的扭矩。 对其余线束组件重复此过程。
Show/hide table
图 6 | g01404680 |
- 重新安置并连接线束组件 (17) 。 安装新的电缆系带 (16) 。
Show/hide table
图 7 | g01404679 |
- 连接软管组件 (15) 。
Show/hide table
图 8 | g01404677 |
- 连接软管 (13) 和软管组件 (14) 。 拧紧卡箍 (12) 。
Show/hide table
图 9 | g01404676 |
- 充注空调系统中的空调制冷剂。 请参阅操作和保养手册, "容量(加注)"以了解正在维护的机器的正确加注量。 请参阅维修手册, SENR5664, "使用 R-134a 制冷剂的空调与暖风系统",了解相关正确步骤。 有关正确的工具,请参阅专门出版物, NEDG2500, "空调工具"。
Show/hide table
接触制冷剂会使人受伤。 接触制冷剂会造成冻伤。 让手、脸避开,有助于防止受伤。 制冷管路被打开时,即使压力计显示系统中已经没有制冷剂,也要始终戴着护目镜。 拆卸管件时,务必小心谨慎。 慢慢地拧松接头。 如果系统内仍有压力,就要把它缓慢地释放到一个通风良好的地方去。 通过燃着的香烟吸入制冷剂会使人受伤或死亡。 通过燃着的香烟或其他抽烟方法吸入空调制冷气体,或者,吸入空调制冷气体接触明火而形成的烟雾,都会造成对人体的伤害 或死亡。 维修空调时,或者,在任何可能存在制冷气体的地方都不要抽烟。 采用经过认可的回收和循环利用车妥善地从空调器中取出制冷剂。 |
- 将阀 (11) 转到打开位置。
Show/hide table
图 10 | g01404674 |
- 连接软管组件 (10) 。
Show/hide table
图 11 | g01404673 |
- 连接软管 (8) 和线束组件 (9) 。
Show/hide table
图 12 | g01404672 |
- 连接软管组件 (7) 。
Show/hide table
图 13 | g01404671 |
- 连接卡箍 (6) 。
Show/hide table
图 14 | g01404670 |
- 连接软管组件 (5) 。
Show/hide table
图 15 | g01404669 |
- 安装面板 (3) 和螺栓 (4) 。
Show/hide table
图 16 | g01404668 |
- 安装罩盖 (2) 。
Show/hide table
图 17 | g01404666 |
- 安装螺栓 (1) ,并在另一侧重复该步骤。
Show/hide table
图 18 | g01404665 |
- 对泵和制动器排气。 请参阅测试和调整, "齿轮泵(制动器、举倾机构、液压风扇)- 排气"。
End By:
- 拆下销后降下车斗。 请参阅 拆解和组装, "销(车斗固定)- 拆卸和安装"。
- 安装曲轴箱防护罩。 请参阅 拆解和组装, "护罩(发动机油底壳)- 拆卸和安装"。
- 安装发动机面板。 请参阅 拆解和组装, "噪音抑制面板 - 拆卸和安装"。
- 安装罩。 请参阅 拆解和组装, "罩(散热器)- 拆卸和安装"。
Caterpillar Information System:
770 and 772 Off-Highway Truck/Tractors Cab - Remove
160M Motor Grader Machine Systems Secondary Steering Pump and Motor - Install
160M Motor Grader Machine Systems Secondary Steering Pump and Motor - Remove
2007/08/20 Improved Sealing for Torque Limiter on Hydraulic Pump {5070}
160M Motor Grader Machine Systems Control Manifold (Steering Backup) - Install
160M Motor Grader Machine Systems Control Manifold (Steering Backup) - Remove
854K Wheel Dozer Camera - Clean - If Equipped
C7 Engines for Caterpillar Built Machines Engine Oil Filter Base
160M Motor Grader Machine Systems Steering Control Valve - Install
2007/08/20 New Routing of Hoses on the Extendable Stick Bucket Improves Service Life {5057, 6533}
770 and 772 Off-Highway Truck/Tractors Hydraulic Tank (Hoist, Brake) - Install
770 and 772 Off-Highway Truck/Tractors Hydraulic Tank (Hoist, Brake) - Remove
CP54 and CS54 Vibratory Soil Compactors Machine Systems Front Bumper
2007/08/27 Improved Engine Software is Used {7620}
2007/08/13 The Edge Filter Is Now Removed from Fuel Nozzles {1254, 1290}
C7 and C9 Engines for Caterpillar Built Machines CID 0164 FMI 11 Injector Actuation Pressure system fault
2007/08/27 A New Battery Disconnect Switch Improves Battery Life {1402, 1411, 7257}
2007/08/20 The Edge Filter Is Now Removed from Fuel Nozzles {1254, 1290}
14L Motor Grader Steering Frame Lock - Separate and Connect
Fuel Sender Leaks on C-Series Multi Terrain Loaders and Skid Steer Loaders{1273} Fuel Sender Leaks on C-Series Multi Terrain Loaders and Skid Steer Loaders{1273}
CP54 and CS54 Vibratory Soil Compactors Machine Systems Air Conditioner Group
CP76 and CS76 Vibratory Soil Compactors Machine Systems Drum - Install
14L Motor Grader Gear Group (All Wheel Drive) - Remove
2007/08/27 An Improved Secondary Steering Valve Mount is Now Used {4339}