Front Frame from Rear Frame (Articulating Hitch) - Separate
分离步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 155-3597     | 止轮块     | 8     |
B     | 9U-7540     | 提升台架     | 2     |
C     | 8T-5255     | 液压千斤顶     | 1     |
D     | 1P-1837     | 轴承拆卸工具适配器     | 1     |
1P-1838 | 轴承拆卸工具适配器     | 1     | |
6V-3170 | 双作用油缸     | 1     | |
4C-9634 | 拉拔器螺柱     | 1     | |
4K-0684 | 硬垫圈     | 1     | |
3S-6224 | 电动液压泵总成     | 1     | |
9U-6832 | 螺母     | 1     | |
FT-2549 | 套筒     | 1     | |
E     | 1P-1837     | 轴承拆卸工具适配器     | 1     |
1P-1838 | 轴承拆卸工具适配器     | 1     | |
6V-3170 | 双作用油缸     | 1     | |
4C-9634 | 拉拔器螺柱     | 1     | |
4K-0684 | 硬垫圈     | 1     | |
9U-6832 | 螺母     | 1     | |
3S-6224 | 电动液压泵总成     | 1     | |
8B-7555 | 接头     | 2     | |
0S-1602 | 螺栓     | 2     | |
F     | 6V-3142     | 板     | 1     |
开始:
- 拆下裂土器。 请参阅拆解和装配, "裂土器 - 拆卸"。
- 拆下发动机护罩。 请参阅拆解和组装, "发动机护罩 - 拆卸"。
- 把驱动轴取下。 请参考拆解和装配, "驱动轴 - 拆卸和安装"。
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 连接转向机架锁。 请参阅操作和保养手册, "转向机架锁"。
- 将铲刀降至地面。
- 将蓄电池断路开关转到断开位置。 请参阅操作和维护手册, "蓄电池断路开关"。
- 回收空调系统中的空调制冷剂。 请参阅维修手册, SENR5664, "使用 R-134a 制冷剂的空调与暖风系统",了解相关正确步骤。 请参考代理商维修工具目录, NENG2500, "空调工具"以了解正确的工具。
Show/hide table
接触制冷剂会使人受伤。 接触制冷剂会造成冻伤。 让手、脸避开,有助于防止受伤。 制冷管路被打开时,即使压力计显示系统中已经没有制冷剂,也要始终戴着护目镜。 拆卸管件时,务必小心谨慎。 慢慢地拧松接头。 如果系统内仍有压力,就要把它缓慢地释放到一个通风良好的地方去。 通过燃着的香烟吸入制冷剂会使人受伤或死亡。 通过燃着的香烟或其他抽烟方法吸入空调制冷气体,或者,吸入空调制冷气体接触明火而形成的烟雾,都会造成对人体的伤害 或死亡。 维修空调时,或者,在任何可能存在制冷气体的地方都不要抽烟。 采用经过认可的回收和循环利用车妥善地从空调器中取出制冷剂。 |
Show/hide table
按照建议的步骤拆卸和安装轮胎和/或车轮组件。 确保始终正确支撑住机器以及轮胎和/或车轮组件。 采用不正确的步骤拆卸和安装轮胎和/或车轮组件可造成人员伤亡。 |
- 释放系统压力。 请参阅操作和保养手册, "系统压力 - 释放"。
- 将液压系统中的油排入合适的容器以便保存或废弃这些油。 请参阅操作和保养手册, "容量 - 加注"。 请参阅操作和保养手册, "液压系统机油 – 更换"。
- 将发动机冷却液排入合适的容器,以便保存或弃置。 请参阅操作和保养手册, "冷却系统长效冷却液 - 更换"。
- 使用工具 (A) 楔住车轮 (1) 。 在对面重新执行此步骤。
Show/hide table
图 1 | g01382865 |
Show/hide table
图 2 | g01382869 |
- 将适当的挡块安装到前机架 (2) 和车轮倾斜杆 (3) 之间。 安装锁销 (4) 。
Show/hide table
图 3 | g01382973 |
- 拆下护罩 (5) 。 在对面重新执行此步骤。
Show/hide table
图 4 | g01382978 |
- 断开线束组件 (6) 并拆下连接紧固件。 断开软管 (7) 。 断开线束组件 (8) 。
Show/hide table
图 5 | g01383014 |
- 断开线束组件 (9) 并拆下连接紧固件。
Show/hide table
图 6 | g01383018 |
- 拆下夹子 (10) 。
Show/hide table
图 7 | g01383069 |
- 拆下夹子 (11) 。
Show/hide table
图 8 | g01383079 |
- 卸下夹子 (12) 和夹子 (13) 。 拆下板 (14) 和挡块 (15) 。 拆下卡箍 (16) 。 拆下板 (17) 和挡块 (18) 。
Show/hide table
图 9 | g01383083 |
- 拆下夹子 (19) 。
Show/hide table
图 10 | g01383104 |
- 断开线束组件 (20) 。 拆卸夹子 (21) 。
Show/hide table
图 11 | g01383110 |
- 断开软管组件 (22) 。 拆下夹子 (23) 和夹子 (24) 。 拆下板 (25) 和挡块 (26) 。
Show/hide table
图 12 | g01383127 |
- 断开软管组件 (27) 和软管组件 (28) 。 拆下夹子 (29) 。 断开软管组件 (30) 。
Show/hide table
图 13 | g01383130 |
- 断开软管组件 (31) 和软管组件 (32) 。
Show/hide table
图 14 | g01383150 |
- 断开软管组件 (33) 。
Show/hide table
图 15 | g01383157 |
- 拆下夹子 (34) 。 拆下板 (35) 和挡块 (36) 。 拆下板 (37) 和挡块 (38) 。
Show/hide table
图 16 | g01383161 |
- 断开接地母线 (39) 。
Show/hide table
图 17 | g01383175 |
- 将适当的起吊设备固定到铰接油缸 (40) 上。 拆下开口销 (41) 。 拆下销组件 (42) 。 将铰接油缸 (40) 放到一边。 对其余的铰接油缸 (40) 重复此步骤。
Show/hide table
图 18 | g01383176 |
- 断开软管组件 (43) 。 断开连杆组件 (44) 。
Show/hide table
图 19 | g01383360 |
- 卸下支架组件 (45) 。
Show/hide table
图 20 | g01383374 |
- 拆下螺栓 (46) 。 拆下螺栓 (47) 。 拆下盖 (48) 。
Show/hide table
图 21 | g01383378 |
- 断开软管组件 (49) 。
Show/hide table
图 22 | g01383619 |
- 使用工具 (C) 和适当的起吊设备拆卸销 (50) 。
Show/hide table
图 23 | g01383432 |
- 利用工具 (B) 和适当的挡块支撑前机架 (2) 。
Show/hide table
图 24 | g01383439 |
- 断开转向机架锁。 请参阅操作和保养手册, "转向机架锁"。
- 拆下螺栓 (51) 和螺栓 (52) 。 取下锁板 (53) 。
Show/hide table
图 25 | g01383449 |
- 卸下垫片 (54) 。
注: 为了便于安装,记下垫片 (54) 的数量和次序。
Show/hide table
图 26 | g01383454 |
- 拆下隔套 (55) 。 利用工具 (C) 拆下销 (56) 。
Show/hide table
图 27 | g01383462 |
- 将适当的叉车安置在后机架 (57) 的后部。 将两个适当的起吊设备固定在后机架和叉具上。 从后轮 (1) 上卸下工具 (A) 。
Show/hide table
图 28 | g01383497 |
- 使用适当的叉车将后机架 (56) 与前机架分离。
- 使用工具 (C) 和工具 (F) 拆下套环 (58) 。
Show/hide table
图 29 | g01383541 |
- 使用工具 (E) ,卸下轴承套 (59) 。
Show/hide table
图 30 | g01383543 |
- 拆下唇型密封 (60) 。
Show/hide table
图 31 | g01383553 |
- 利用工具 (D) 拆下轴承 (61) 。
Show/hide table
图 32 | g01383558 |
- 拆下隔套 (62) 。 拆下螺栓 (63) 。 拆卸下盖 (65) 。 拆下上盖 (64) 。 卸下垫片 (66) 。
注: 为了便于安装,记下垫片 (66) 的数量和次序。
Show/hide table
图 33 | g01383564 |
- 拆下唇型密封 (67) 。
Show/hide table
图 34 | g01383568 |
- 拆下唇型密封 (68) 。
Show/hide table
图 35 | g01383572 |
- 拆下轴承组件 (69) 。
Show/hide table
图 36 | g01383579 |
Caterpillar Information System:
450E Backhoe Loader Machine Systems Bank Valve (Backhoe) - Remove
450E Backhoe Loader Machine Systems Bank Valve (Loader) - Install
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Manifold (Pilot Operated) - Inlet Manifold for the Backhoe
Installation of the AccuGrade® - Grade Control System for the Motor Graders{7220} Installation of the AccuGrade® - Grade Control System for the Motor Graders{7220}
24M Motor Grader Power Train Electronic Control System MID 027 - CID 0681 - FMI 06
24M Motor Grader Power Train Electronic Control System MID 027 - CID 0681 - FMI 05
24M Motor Grader Power Train Electronic Control System MID 027 - CID 0681 - FMI 03
770 and 772 Off-Highway Truck/Tractors Pin (Body Retaining) - Remove and Install
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Manifold (Pilot Operated) - Inlet Manifold for the Loader
2007/05/28 A new Hose is Used for the Inlet to the Turbocharger {1051, 1054}
2007/06/04 A Dye is Now Added to the Engine Oil at the Factory {1348}
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Manifold (Pilot Operated) - Inlet Manifold for the Loader
Installing the 307-6237 Roading Lights Mounting Gp (KIT) (GERMANY) (ITALY){1429} Installing the 307-6237 Roading Lights Mounting Gp (KIT) (GERMANY) (ITALY){1429}
16M Motor Grader Machine Systems Front Frame to Rear Frame (Articulating Hitch) - Connect
2007/08/27 A New Temperature Gauge is Used {7450}
IT38H Integrated Toolcarrier and 938H Wheel Loader Steering System Secondary Steering System
2009/08/24 An Improved Solenoid Valve Group Is Used In Transmissions With ICM For Increased Reliability And Longer Service Life {3124, 3167, 3174}
2007/05/28 An Improved Battery Isolation Control is Now Used {1402, 1408}
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Priming Pump and Fuel Filter Base - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injection Lines - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector Cover - Remove and Install
C6.6 Engines For Caterpillar Built Machines CID 2417 FMI 05
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector - Remove
C6.6 Engines For Caterpillar Built Machines CID 2417 FMI 06