160M Motor Grader Power Train Caterpillar


Gear Pump (Transmission Charging and Scavenge) - Install

Usage:

160M B9E

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.



    Illustration 1g01382489

  1. Install O-ring seals (11) and (10).


    Illustration 2g01382290

  2. Use two people in order to position gear pump (9) to the machine. The weight of gear pump (9) is approximately 34 kg (75 lb). Install bolts (8). Tighten bolts (8) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).

  3. Connect tube assembly (7).


    Illustration 3g01382278

  4. Position screen assembly (6) and install three bolts (5). Tighten bolts (5) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).


    Illustration 4g01382271

  5. Connect hose assemblies (4) and (3).

  6. Position hose assembly (1) and install bolts (2).

  7. Fill the transmission with transmission oil. Refer to Operation and Maintenance Manual, "Transmission and Differential Oil - Change".

End By:

  1. Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".

Caterpillar Information System:

C6.6 Engines For Caterpillar Built Machines CID 0549 FMI 02
C6.6 Engines For Caterpillar Built Machines CID 0267 FMI 04
R1600G Load Haul Dump Autodig System - If Equipped
621H, 623H, and 627H Wheel Tractor-Scrapers Hydraulic and Steering System Flow Switch (Secondary Steering)
R1600G Load Haul Dump Fire Suppression System (Foam) - If Equipped
R1600G Load Haul Dump Fire Suppression System - Check - If Equipped
2007/05/28 New Wheel is Used on Landfill Compactor. {4206}
160M Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Remove
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Valve (Tilt)(Pilot Operated)
450E Backhoe Loader Machine Systems Boom Cylinder - Remove and Install
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Valve (Tilt)(Pilot Operated)
2007/07/30 An Improved Bogie Wheel Gp Is Available {4150, 4192, 4197, 7050}
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Valve (Auxiliary)(Loader)(Pilot Operated)
16M Motor Grader Machine Systems Ripper - Remove
16M Motor Grader Machine Systems Ripper - Install
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Before Roading the Machine
16M Motor Grader Machine Systems Solenoid Valve and Manifold (Hydraulic Fan) - Remove and Install
160M Motor Grader Engine Supplement Engine - Remove
2007/06/04 A Dye is Now Added to the Engine Oil at the Factory {1348}
160M Motor Grader Engine Supplement Engine - Install
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Manifold (Pilot Operated) - Inlet Manifold for the Loader
2007/06/04 A Dye is Now Added to the Engine Oil at the Factory {1348}
2007/05/28 A new Hose is Used for the Inlet to the Turbocharger {1051, 1054}
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Manifold (Pilot Operated) - Inlet Manifold for the Loader
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.