Turbocharger - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 5P-3931     | 防粘结剂     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
卡箍组件应只使用一次。 使用后弃置所有卡箍组件。 |
Show/hide table
注意 |
---|
波纹管组件应只使用一次。 使用后弃置所有波纹管。 |
- 将适当起吊设备连在涡轮增压器 (3) 上。 涡轮增压器 (3) 的重量约为 135 kg (300 lb)。
Show/hide table
图 1 | g01351521 |
- 将涡轮增压器 (3) 放置在安装支架上。 将工具 (A) 涂敷在螺栓 (5) 的螺纹上。 安装螺栓 (5) 。 此时请勿拧紧螺栓 (5) 。
- 安装管组件 (4) 。 连接管 (9) 、管组件 (8) 和管组件 (6) 。
- 将工具 (A) 涂抹在螺纹、轴承表面以及卡箍组件 (7) 的内表面。 安装新的波纹管组件 (10) 、螺栓 (11) 以及新的卡箍组件 (7) 。 把卡箍组件 (7) 拧紧至扭矩为 10 ± 1 N·m (90 ± 9 lb in)。 用软锤在卡箍组件的直径四周轻轻敲打。 把卡箍组件 (7) 拧紧至扭矩为 10 ± 1 N·m (90 ± 9 lb in)。
注: 在安装过程中,确保波纹管组件处于正确的朝向。 波纹管组件的顶部之间间距应相等
- 将工具 (A) 涂抹在螺纹、轴承表面、卡箍组件 (2) 的内表面以及卡箍组件 (1) 上。 将新的波纹管组件、新的卡箍组件 (2) 和新的卡箍组件 (1) 安装在涡轮增压器 (3) 上。 把卡箍组件 (2) 和卡箍组件 (1) 拧紧至扭矩为 7.5 ± 1.0 N·m (65 ± 9 lb in)。 用软面锤轻轻敲打卡箍组件外缘。 把卡箍组件 (2) 和卡箍组件 (1) 拧紧至扭矩为 7.5 ± 1.0 N·m (65 ± 9 lb in)。
Show/hide table
图 2 | g01351417 |
注: 在安装过程中,确保波纹管组件处于正确的朝向。 流向箭头的方向应指向正确的方向。 波纹管组件的顶部之间间距应相等
- 将固定涡轮增压器 (3) 的螺栓拧紧至标准扭矩。
- 安装空气滤清器。
- 向冷却系统加注冷却液。 请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
Caterpillar Information System:
C11 and C13 On-Highway Engines Camshaft
325D and 329D Excavators and 325D Material Handler Machine System Specifications Oil Filter (Hydraulic) - Case Drain
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Thermostatic Valve - Install
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Thermostatic Valve - Assemble
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Thermostatic Valve - Disassemble
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Thermostatic Valve - Remove
G3408 and G3412 Engines Carburetor Control Linkage
CX35 On-Highway Transmission Transmission Planetary - Disassemble
C7 On-highway Engine Air Inlet Elbow
CX35 On-Highway Transmission Speed Sensor (Transmission)
2007/04/02 Understanding Transmission Filter Plugging Events {3004, 3067}
CX35 On-Highway Transmission Oil Filter (Transmission)
C3.4 Engines for Caterpillar Built Machines Engine Design
Replacing and Repositioning the Particulate Trap Exhaust Filter Module on Mass Transit Buses{7490} Replacing and Repositioning the Particulate Trap Exhaust Filter Module on Mass Transit Buses{7490}
C3.4 Engines for Caterpillar Built Machines Exhaust Manifold
C13, C15, and C18 Tier 4 Final Engines Crankshaft
3508C, 3512C and 3516C Marine Engines Aftercooler - Remove and Install
Procedure for Replacing the Particulate Trap Exhaust Filter or the Catalyzed Continuously Regenerating Technology (CCRT) Filter{1091, 7490} Procedure for Replacing the Particulate Trap Exhaust Filter or the Catalyzed Continuously Regenerating Technology (CCRT) Filter{1091, 7490}
2007/02/26 Packaging the Turbocharger {1052}
2007/03/01 Packaging the Turbocharger {1052}
C9 On-highway Engine Engine to Transmission Adapter
C3.4 IND Industrial Engine Model View Illustrations
C4.4 (Mech) Industrial Engine Fuel System
C3.4 Engines for Caterpillar Built Machines Camshaft