Front Axle - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 9U-7536     | 起吊台架     | 1     |
4C-5809 | 电动液压泵总成     | 1     | |
B     | 8S-7615     | 销     | 1     |
8S-7640 | 台架     | 1     | |
8S-7611 | 管     | 1     | |
C     | 1P-1835     | 轴承拆卸工具适配器     | 1     |
4C-9634 | 拉拔器螺柱     | 1     | |
6V-3170 | 双作用油缸     | 1     | |
3S-6224 | 电动液压泵总成     | 1     | |
9U-6832 | 螺母     | 1     |
开始:
- 拆下前轮。 请参阅拆解和组装, "车轮 - 拆卸和安装"。
- 卸下车轮倾斜杆。 请参阅拆解和组装, "车轮倾斜杆 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 释放系统压力。 请参阅操作和保养手册, "系统压力 - 释放"。
- 将液压油排入适当的容器以便存储或处理。 请参阅操作和保养手册, "液压系统机油 – 更换"。
- 使用工具 (A) 和工具 (B) 支撑牵引杆 (1) 和前轴。
Show/hide table
图 1 | g01341448 |
- 断开软管组件 (2) 、软管组件 (3) 、软管组件 (4) 、软管组件 (5) 和软管组件 (6) 。
Show/hide table
图 2 | g01341449 |
- 断开软管组件 (7) 、软管组件 (8) 和软管组件 (9) 。
Show/hide table
图 3 | g01341446 |
- 断开线束组件 (10) 。 断开线束组件 (11) 。 拆下夹子 (12) 。
Show/hide table
图 4 | g01341456 |
- 将两台适当的起吊设备连接至前轴 (13) 上。 前轴 (13) 的重量约为 907 kg (2000 lb)。
Show/hide table
图 5 | g01341459 |
Show/hide table
图 6 | g01341447 |
- 卸下螺栓 (14) 以卸下销组件 (15) 。
Show/hide table
图 7 | g01341452 |
- 卸下板 (16) 和垫圈 (17) 。
Show/hide table
图 8 | g01341445 |
- 卸下垫圈 (18) 。
注: 记录垫圈 (18) 的数量和顺序,以便安装。
Show/hide table
图 9 | g01341451 |
- 拆下工具 (B) 。 卸下前轴 (13) 并将前轴 (13) 放置在适当的垛式支架上。
Show/hide table
图 10 | g01341455 |
- 卸下唇形密封 (19) 。
Show/hide table
图 11 | g01341444 |
- 拆下唇形密封 (20) 。
Show/hide table
图 12 | g01341442 |
- 使用工具 (C) 卸下轴承 (21) 。
Show/hide table
图 13 | g01341458 |
Caterpillar Information System:
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Supplement Radiator - Remove and Install
C4.4 and C6.6 Engines for Caterpillar Built Machines ECM Will Not Communicate with Other Systems or Display Modules
587R Pipelayer Safety Messages - Arrangement II (Cab)
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Supplement Aftercooler - Remove and Install
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Can Not Reach Top Engine RPM
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1757 - FMI 04
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1757 - FMI 03
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1711 - FMI 04
C4.4 and C6.6 Engines for Caterpillar Built Machines System Configuration Parameters
3306C Engines for Caterpillar Built Machines Fan Drive
2007/01/22 A New Service Tool Is Now Available For Paving Compactors {7620}
2007/01/01 A Software Update for the Propel Control System is Now Used on Asphalt Pavers {7610, 7620}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors C6.6 Engine Supplement Radiator, Hydraulic Oil Cooler, Air Cooler, and Fuel Cooler - Separate
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors C6.6 Engine Supplement Radiator, Hydraulic Oil Cooler, Air Cooler, and Fuel Cooler - Connect
PL61 Pipelayer and D6K Track-Type Tractor Using Caterpillar Electronic Technician to Determine Diagnostic Codes
Frame Replacement for the 793B and 793C Off-Highway Trucks{1353, 7000, 7000, 7051} Frame Replacement for the 793B and 793C Off-Highway Trucks{1353, 7000, 7000, 7051}
246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Power Train Solenoid Valve (Motor, 2-Speed) - Remove and Install
287C2 Compact Track Loader and 287C, 277C, 277C2 and 297C Multi Terrain Loaders Machine Systems Control Valve (Work Tool) - Remove - High Flow
2007/01/22 A New Sprocket Bearing Improves Reliability for Multi Terrain Loaders {4164, 7551}
14M Motor Grader Machine Systems Front Axle - Install
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Event Code List
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Fuel Pressure Is Low
3412E Engine for Caterpillar Built Machines System Overview
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Coolant Temperature Is High