816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Caterpillar


MID 081 - CID 1693 - FMI 01

Usage:

814F II BXG


Conditions Which Generate This Code:


Illustration 1g01341036

Schematic of the Position Sensor (Decelerator Pedal)

This diagnostic code is associated with the Position Sensor (Decelerator Pedal). The FMI 01 means that the ECM has determined that the signal of the sensor is below the normal range.

The possible causes of this failure are listed below:

  • The position sensor has failed.

  • The signal circuit of the sensor is shorted to the ground.

  • The sensor needs to be calibrated.

  • The ECM has failed. This is unlikely.

Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected.

Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.

Test Step 1. INSPECT THE SENSOR.

  1. Perform a visual inspection of the sensor, the wiring for the sensor and the hardware that is associated with the sensor.

Expected Result:

There is no apparent damage to the sensor, the wiring for the sensor or the hardware that is associated with the sensor.

Results:

  • OK - There is no apparent damage to the sensor, the wiring for the sensor or the hardware that is associated with the sensor. Proceed to Test Step 2.

  • NOT OK - There is apparent damage to the sensor, the wiring for the sensor or the hardware that is associated with the sensor.

    Repair: Replace the damaged part.

    Proceed to Test Step 8.

Test Step 2. CHECK FOR POWER AT THE SENSOR.

  1. Do not disconnect the harness connector from the sensor.

  1. At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along the voltage supply wire (contact A).

  1. Turn the key start switch and the disconnect switch to the ON position.

  1. Measure the voltage from contact A to frame ground.

Expected Result:

The voltage measurement is approximately battery voltage.

Results:

  • OK - The voltage is approximately battery voltage. Proceed to Test Step 3.

  • NOT OK - The voltage is not approximately battery voltage. The circuit is open.

    Repair: Repair the machine harness or replace the machine harness.

    STOP

Test Step 3. CHECK FOR PROPER GROUND AT THE SENSOR.

  1. The machine harness remains connected to the sensor.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. Remove the 7X-1710 Multimeter Probe from the voltage supply wire (contact A).

  1. At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along the ground wire (contact B).

  1. Measure the resistance from contact B to frame ground.

Expected Result:

The resistance is less than 5 ohms.

Results:

  • OK - The resistance is less than 5 ohms. The ground circuit is correct. Proceed to Test Step 4.

  • NOT OK - The resistance is greater than 5 ohms. The ground circuit in the machine harness has failed.

    Repair: Replace the machine harness or repair the machine harness.

    STOP

Test Step 4. CHECK THE SIGNAL OF THE SENSOR.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. At the back of the harness connector for the sensor, remove the 7X-1710 Multimeter Probe from contact B and insert the probe along the signal wire (contact C).

  1. At the back of the harness connector for the sensor, insert the 7X-1710 Multimeter Probe along the ground wire (contact B).

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Monitor the signal of the sensor with the 146-4080 Digital Multimeter .

  1. Without disconnecting the sensor or the hardware that is associated with the sensor from the machine, take the sensor through the full operating range of the sensor.

    Note: On some machines, it may be necessary to start the engine in order to take the sensor through the full operating range of the sensor.

Expected Result:

The sensor's signal responds in the manner that is described at the beginning of this procedure. The CID 1693 FMI 01 is not active at the maximum range of the sensor.

Results:

  • OK - The sensor's signal responds correctly. The sensor is operating correctly. Proceed to Test Step 5.

  • NOT OK - The sensor's signal does not respond correctly. The sensor is NOT operating correctly.

    Repair: Replace the sensor.

    STOP

Test Step 5. CHECK THE SIGNAL AT THE ECM.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. Insert the 7X-1710 Multimeter Probes into the back of the ECM connector along J1-16 (wire 202-BK) and J2-4 (wire H722-GN).

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Monitor the signal of the sensor with the 146-4080 Digital Multimeter .

  1. Without disconnecting the sensor or the hardware that is associated with the sensor from the machine, take the sensor through the full operating range of the sensor.

    Note: On some machines, it may be necessary to start the engine in order to take the sensor through the full operating range of the sensor.

Expected Result:

The sensor's signal responds in the manner that is described at the beginning of this procedure. The CID 1693 FMI 01 is not active at the maximum range of the sensor.

Results:

  • OK - The sensor's signal responds correctly. The sensor is operating correctly. Proceed to Test Step 6.

  • NOT OK - The sensor's signal does not respond correctly. The harness has failed.

    Repair: Repair the machine harness or replace the machine harness.

    STOP

Test Step 6. CHECK THE SIGNAL CIRCUIT FOR A SHORT IN THE HARNESS.

  1. The key start switch and the disconnect switch remain in the OFF position.

  1. Disconnect the machine harness connectors from the sensor and the ECM.

  1. Measure the resistance between contact J2-4 (wire H722-GN) and all contacts that are used in the machine harness connectors for the ECM.

Expected Result:

Each resistance measurement is greater than 5000 ohms.

Results:

  • OK - Each of the resistance measurements are greater than 5000 ohms. The circuit is correct. Proceed to Test Step 7.

  • NOT OK - The resistance is less than 5 ohms. The signal circuit is shorted to another circuit in the harness.

    Repair: Repair the machine harness or replace the machine harness.

    STOP

Test Step 7. CHECK IF THE DIAGNOSTIC CODE REMAINS

  1. Inspect the harness connectors and clean the contacts of the machine harness connectors.

  1. Reconnect all harness connectors.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Operate the machine and take the sensor through the operating range of the sensor.

  1. Check the status of the CID 1693 FMI 01.

Expected Result:

The CID 1693 FMI 01 is not active at the minimum range of the sensor.

Results:

  • OK - The CID 1693 FMI 01 is not active at the minimum range of the sensor. The diagnostic code does not exist at this time. The initial diagnostic code was probably caused by a poor connection or a short at one of the connectors that was disconnected and reconnected. Resume normal operation.STOP

  • NOT OK - The CID 1693 FMI 01 is active at the minimum range of the sensor. The diagnostic code has not been corrected. The ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure. Perform the adjustment procedure for the sensor, if necessary. Then perform the calibration procedure for the sensor. Perform this procedure again. If the cause of the failure is not found, replace the ECM. See the Testing and Adjusting, "Electronic Control Module (ECM) - Replace".

    STOP

Test Step 8. CHECK THE ADJUSTMENT AND/OR THE CALIBRATION OF THE SENSOR.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Perform the adjustment procedure for the position sensor, if necessary. Then perform the calibration of the position sensor. Refer to the Testing and Adjusting, "Position Sensor (Left Brake Pedal) (Decelerator) (Electronic Technition) - Calibrate" for additional information on these procedures.

  1. Without disconnecting the sensor or the hardware that is associated with the sensor, move the sensor through the entire range of motion.

    Note: On some machines, it may be necessary to start the engine in order to move the sensor through the entire range of motion.

  1. Check the status of the diagnostic code.

Expected Result:

The CID 1693 FMI 01 is not active.

Results:

  • OK - The diagnostic is not active. The adjustment and/or the calibration has corrected the failure. Resume normal operation.STOP

  • NOT OK - CID 1693 FMI 01 is still active.

    Repair: Exit this procedure. Perform this procedure again.

    STOP

Caterpillar Information System:

2007/09/10 An Improved Rotary Beacon is Now Used on Cold Planers {1431}
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1693 - FMI 00
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 0562 - FMI 09
279C2 Compact Track Loader and 287C, 277C, 277C2 and 297C <BR>Multi Terrain Loaders Engine Supplement Gear Motor (Fan, Aftercooler) - Remove
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors C6.6 Engine Supplement Muffler - Remove and Install
770, 772, 773F and 777F Off-Highway Truck/Tractors and 775F Quarry Truck Monitoring System Monitor Menu
2007/03/05 An Improved Hose Assembly in the Water Lines Group {1380}
IT38H Integrated Toolcarrier and <BR>938H Wheel Loader <BR>Engine Supplement Engine Compartment Shield - Remove and Install
14L Motor Grader Power Train Rear Axle
777G Off-Highway Truck Power Train Hydraulic and Transmission Tank (Torque Converter, Hoist, Brake) - Install
279C2 Compact Track Loader and 287C, 277C, 277C2 and 297C <BR>Multi Terrain Loaders Engine Supplement Gear Motor (Fan, Aftercooler) - Assemble
279C2 Compact Track Loader and 287C, 277C, 277C2 and 297C <BR>Multi Terrain Loaders Engine Supplement Gear Motor (Fan, Aftercooler) - Disassemble
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1693 - FMI 03
279C2 Compact Track Loader and 287C, 277C, 277C2 and 297C <BR>Multi Terrain Loaders Engine Supplement Gear Motor (Fan, Aftercooler) - Install
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1693 - FMI 04
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1693 - FMI 13
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1711 - FMI 03
IT38H Integrated Toolcarrier and <BR>938H Wheel Loader <BR>Engine Supplement Fan and Gear Motor (Hydraulic Fan) - Remove
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Sound Information and Vibration Information
2007/01/01 A Software Update for the Propel Control System is Now Used on Asphalt Pavers {7610, 7620}
2007/01/22 A New Service Tool Is Now Available For Paving Compactors {7620}
3306C Engines for Caterpillar Built Machines Fan Drive
C4.4 and C6.6 Engines for Caterpillar Built Machines System Configuration Parameters
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1711 - FMI 04
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.