C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Caterpillar


Crankcase Breather - Remove and Install - Turbocharged Engines

Usage:

CB-22 220

拆卸步骤


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损並縮短部件使用寿命。



注意

在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。

按照本地法规和指令处置所有液体。




    图 1g01310618
    典型示例

    ------ WARNING! ------

    弹簧加压的零件和/或盖板可能导致人身伤害。

    拆卸盖板时弹簧力将被释放。

    松动螺栓时做好准备把持住弹簧加载的盖板。


  1. 拆下螺栓 (1),然后拆下盖 (2)、弹簧 (3) 和膜片 (4) 的组件。 记下盖 (2) 的方位。

  2. 从盖 (2) 上拆下弹簧 (3) 和膜片 (4)。

  3. 将适配器 (5) 和接头 (6) 从气门机构盖 (7) 上拆下。

    注: 作临时标记以指示适配器的方位,方便安装。

  4. 如有必要,遵循步骤 4.a 至 4.c 以便拆下呼吸器的滤网。

    1. 拆下气门机构盖 (7)。 请参考拆解和组装, "气门机构盖 - 拆卸和安装"以了解正确步骤。

    2. 拆下螺钉 (9),然后小心地拆下板 (10)。

    3. 从气门机构盖 (7) 上拆下滤网 (8)。

安装步骤

表 1
所需工具 
工具  零件号  零件描述  数量 
A  Loctite 594   
B  247-5377  扭矩扳手 


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损並縮短部件使用寿命。



注意

确保呼吸器总成零部件正确安装。如果呼吸器总成不能正常工作,发动机可能发生损坏。




    图 2g01310618
    典型示例

  1. 清洁并检查所有零件。 更换任何损坏或磨损的零件。 确保气门机构盖中的呼吸器凹槽清洁。 确保适配器 (5) 上的通风孔和盖 (2) 上的通风孔未堵塞。

  2. 如有必要,遵循步骤 2.a 至 2.e,以便安装呼吸器的滤网。

    1. 将滤网 (8) 安装到气门机构盖 (7) 上。

    2. 将一滴工具 (A) 涂抹到气门机构盖 (7) 上的板配合面上。

    3. 将板 (10) 放置在气门机构盖 (7) 上,安装螺钉 (9)。

    4. 拧紧螺钉 (9) 至扭矩为 1.5 N·m (13 lb in)

    5. 安装气门机构盖 (7)。 请参考拆解和组装, "气门机构盖 - 拆卸和安装"以了解正确步骤。

  3. 将新接头 (6) 放到气门机构盖上并安装适配器 (5)。

    注: 确保适配器的方位正确。 通风孔应朝上。

    ------ WARNING! ------

    被弹簧力爆出的零件击中,会招致人员伤害。

    确保穿上所有必要的保护装备。

    遵照建议的程序,并使用所有建议的工具以释放弹簧力。


  4. 将膜片 (4) 和弹簧 (3) 安装到盖 (2) 上。

  5. 将盖 (2)、弹簧 (3) 和膜片 (4) 的组件放置在气门机构盖 (7) 上。

    注: 确保盖的方位正确。

  6. 安装螺栓 (1)。 使用工具 (B) 拧紧螺栓至扭矩 3 N·m (27 lb in)

Caterpillar Information System:

C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankcase Breather - Remove and Install - Naturally Aspirated Engines
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Coolant Temperature Switch - Remove and Install - C1.1, C1.5, C1.6 and C2.2 Engines
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Coolant Temperature Switch - Remove and Install - C0.5 and C0.7 Engines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting rods in position
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Connecting Rod Bearings - Install - Connecting rods in position
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Camshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Camshaft - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Disassemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Assemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 65 Amp and 85 Amp Alternators
C13 On-highway Engine Air Lines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 55 Amp Alternator
G3520C and G3520E Generator Set Engines Turbocharger Compressor Bypass - Test
G3520C and G3520E Generator Set Engines Detonation - Test
C11 and C13 Engines and 14M and 16M Motor Graders CAN Data Link - Test
G3520C and G3520E Generator Set Engines Electrical Power Supply - Test
C9 Engines for Motor Graders Fuel Filter Differential Pressure - Test
C11 and C13 Engines and 14M and 16M Motor Graders Fuel Filter Is Restricted
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290} Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
C13 On-highway Engine Air Lines
C11 and C13 Engines and 14M and 16M Motor Graders Fuel Transfer Pump - Test
G3520C and G3520E Generator Set Engines Fuel Control - Test
C13 On-highway Engine Air Lines
C11 and C13 Petroleum Engines Air Lines
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.