C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Caterpillar


Alternator - Remove and Install - 55 Amp Alternator

Usage:

CB-22 220

拆卸步骤

开始:

  1. 拆下 V 形皮带。 请参阅拆解和组装, "V 形皮带 - 拆卸和安装"。


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。


  1. 将蓄电池断路开关转到断开位置。

  2. 在线束组件的连接上做出临时的识别标记。


    图 1g01308282
    典型示例

  3. 从交流发电机 (5) 上断开线束组件(未显示)。

  4. 从交流发电机 (5) 上拆下螺栓 (2) 和垫圈 (3)。

  5. 拆下紧固件 (6) 和 (7),然后从安装支架上拆下交流发电机 (5)。

  6. 如有必要,卸下螺栓 (2),然后卸下调节连杆 (4)。

安装步骤



    图 2g01308282
    典型示例

  1. 如有必要,安装调节连杆 (4),然后安装螺栓 (1) 并用手拧紧。

  2. 将交流发电机 (5) 安置在安装支架上。

  3. 安装紧固件 (6) 和 (7) 并用手拧紧。

  4. 安装螺栓 (2) 和垫圈 (3),用手拧紧。

  5. 安装 V 形皮带。 请参阅拆解和组装, "V 形皮带 - 拆卸和安装"。

    注: 确保交流发电机皮带轮与曲轴皮带轮对准。 确保拧紧了所有的紧固件。

  6. 将线束组件(未显示)连接到交流发电机上。

  7. 将蓄电池断路开关转到接通位置。

Caterpillar Information System:

C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 40 Amp Alternator
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 14 Amp and 15 Amp Alternators
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Line - Remove and Install
C13 On-highway Engine Air Lines
G3520C and G3520E Generator Set Engines Turbocharger Turbine Temperature Is Low
G3520C and G3520E Generator Set Engines Oil Filter Differential Pressure Problem
G3520C and G3520E Generator Set Engines Engine Stalls Immediately After Starting
G3520C and G3520E Generator Set Engines Engine Shutdown Is Intermittent
G3520C and G3520E Generator Set Engines Engine Overloads
G3520C and G3520E Generator Set Engines Engine Misfires, Runs Rough or Is Unstable
G3520C and G3520E Generator Set Engines Engine Does Not Crank
G3520C and G3520E Generator Set Engines Engine Cranks but Does Not Start
C13 On-highway Engine Air Lines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 65 Amp and 85 Amp Alternators
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Assemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Disassemble
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Camshaft - Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Camshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Connecting Rod Bearings - Install - Connecting rods in position
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting rods in position
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Coolant Temperature Switch - Remove and Install - C0.5 and C0.7 Engines
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Coolant Temperature Switch - Remove and Install - C1.1, C1.5, C1.6 and C2.2 Engines
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankcase Breather - Remove and Install - Naturally Aspirated Engines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install - Turbocharged Engines
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.