Engine Operation
正确的操作和保养是获得发动机最大使用寿命和经济性的关键因素。 遵循本操作和保养手册中的说明,以便最大限度降低使用费用和延长发动机的使用寿命。
发动机运转过程中频繁观察 Advisor 显示屏或 Caterpillar 电子技师(ET)。 在记录簿上记录仪表数据。 每天记录下运转期间的数据并求出其平均值。 将数据与发动机正常运行的技术规格比较。 经常对比这些数据有助于察觉发动机性能的变化趋向。
调查研究读数的任何显著变化。 监测发动机运行并在发现偏差时采取措施。
根据温度的以下要求施加负荷。 否则可能会导致活塞裙部擦伤或在一些应用中出现卡缸。
- 在您施加负荷到额定负荷 49% 之前,水套水的最低温度为
38 °C (100 °F) 。 最低发动机机油温度为10 °C (50 °F) 。 - 在您施加负荷至额定负荷 50% 到 100% 之前,水套水的最低温度为
50 °C (122 °F) 。 最低发动机机油温度为50 °C (122 °F) 。
带负荷运转的最小转速为 750 rpm。 带负荷运转的最大转速为 1000 rpm。
发动机带负载运转的同时经常检查 Advisor 显示屏和从动设备。 发动机能够在满负荷下持续运转。
在低怠速或在小负荷下长时间运行,可能造成机油消耗量增加并且在气缸中形成积碳。 积碳会造成以下影响:
- 加速部件磨损
- 排放超标
- 爆燃的间隔变小
- 性能不良
- 功率损失
Caterpillar 发动机可以在极轻的载荷下运转有限一段时间而不会造成有害影响。 表 1 列出在不同负载下运转的极限时间。
在到达低负荷运转的时间极限之后,让发动机在高于 70% 额定负荷的负荷下至少运转 2 小时。
例如,发动机在额定载荷的 20% 下运转。 发动机在这个负载因数下运转最长是半小时。 在半小时之后,应使这台发动机在大于 70 % 负载因数下至少运转 2 小时。
为使发动机的保养需求保持在最低程度,应遵照表 1 所列准则。
Show/hide table
低负载运行的时间限制 | |
发动机负荷 | 极限时间 |
0 到 30% | 1/2 小时 |
31 到 50% | 2 小时 |
51 到 100% | 连续功率 (1) |
Show/hide table
(1) | 连续运转时,歧管内空气压力必须大于大气压力。 |
机油消耗率称为制动功率机油消耗率(BSOC)。 其测量单位是每制动千瓦时的克数。 BSOC 取决于发动机型号、工作载荷以及使用的机油。
表 2 列出了下列条件下 G3600 发动机的正常中间寿命 BSOC:
- 100% 的负载系数
- 根据本操作和保养手册, "保养日程表"进行保养。
Show/hide table
G3600 发动机的 BSOC |
|
Caterpillar Information System:
C13 Engine Clean Gas Induction Valve - Disassemble
C13 Engine Inlet and Exhaust Valve Guides - Remove and Install
C13 Engine Cylinder Liner - Remove
3512B Marine Auxiliary Engine Refill Capacities and Recommendations
C11 and C13 Engines and 14M and 16M Motor Graders Cat Data Link - Test
C9 Engines for Motor Graders Configuration Parameters
3512B Marine Auxiliary Engine Product Storage
C280-12 and C280–16 Marine Engines Camshaft - Remove
C15 and C18 Petrolem Generator Set Engines Wiring Information
C11 and C13 Engines and 14M and 16M Motor Graders Electrical Power Supply - Test
3612 and 3616 Engines Cylinder Liner - Install
C11 and C13 Engines and 14M and 16M Motor Graders Cooling Fan Control - Test
C13 Engine Clean Gas Induction Valve - Assemble
C280-12 and C280–16 Marine Engines Camshaft - Install
G3520C and G3520E Engines Pressure Sensor
C175-16 Locomotive Engine Pressure Sensor
C13 Engines for Caterpillar Built Machines Engine Misfires, Runs Rough or Is Unstable
2006/12/25 A New Rear Frame Is Now Used on the Heat Exchanger for Marine Engines {1379}
G3600 Engines Alternator - Inspect
G3600 Engines Belts - Inspect/Adjust/Replace
G3520C and G3520E Generator Set Engines Engine Speed/Timing Sensor
G3520C and G3520E Generator Set Engines General Information
G3520C and G3520E Generator Set Engines Welding Precaution
G3520C and G3520E Generator Set Engines Diagnostic Capabilities