CX31 On-Highway Transmission Power Train Caterpillar


Pump Drive - Install - Rear PTO shaft

Usage:

CX31 B3X

安装步骤

表 1
所需工具    
工具     零件号     零件说明     数量    
A     138-7575     连杆支架     2    
B     1P-2420     变速箱修复台     1    
C     1P-1861     挡圈钳     1    
D     1P-1863     挡圈钳     1    
E     4C-9614     硅密封胶     -    

注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 请勿使用抹布擦干零件。 棉绒可能会留在零件上,从而引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。 尘土及其他污染物可能会损坏精密部件。 组装步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。

注: 检查 O 形密封圈、垫片和密封件有无磨损或损坏。 如有必要,请更换部件。


注意

在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。

有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。

按照当地法规和要求处置所有液体。





    图 1g01300229

  1. 将轴承 (11) 安装到轴组件 (9) 上。 使用工具 (D) 安装挡圈 (10) 。



    图 2g01300228

  1. 安装轴组件 (9) 。 使用工具 (C) 安装挡圈 (8) 。



    图 3g01300227

  1. 将工具 (E) 应用于变矩器壳体和变速箱壳体的接合区域。 将密封垫和油底壳 (6) 放置到位。 用 55 ± 10 N·m (40 ± 7 lb ft)的扭矩拧紧螺栓 (5) 。

  1. 连接线束组件 (7) 。



    图 4g01300224

  1. 安装滤网 (4) 、磁性滤清器 (3) 、盖 (2) 和螺栓 (1) 。



    图 5g01300222

  1. 将工具 (A) 和适当的起吊设备连接在变速箱上。 变速箱的重量约为 544 kg (1200 lb)。 从工具 (B) 上拆卸变速箱。

End By:

  1. 如有必要,安装控制歧管。 请参阅 拆解和组装, "控制歧管 - 安装"。
  2. 如有必要,安装缓速器液压控制阀。 请参阅 拆解和组装, "缓速器液压控制阀 - 拆卸和安装"。

Caterpillar Information System:

CX28 On-Highway Transmission Operational Checks
C11 and C13 Engines and 14M and 16M Motor Graders System Overview
2006/10/02 Improved Instrument Panels are Used {7451}
C11 and C13 Engines and 14M and 16M Motor Graders Electronic Service Tool Does Not Communicate
C280-12 and C280–16 Marine Engines Cylinder Head - Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel DC Bus Current - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Field Coil Current - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Load Cell - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel DC Bus Voltage - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys 4 Wire Output Current - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys AC Output Current - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys In Current - Calibrate
C11 and C13 Engines and 14M and 16M Motor Graders Component Location
C11 and C13 Engines and 14M and 16M Motor Graders Electrical Connectors
C11 and C13 Engines and 14M and 16M Motor Graders Cooling Fan Control - Test
3612 and 3616 Engines Cylinder Liner - Install
C11 and C13 Engines and 14M and 16M Motor Graders Electrical Power Supply - Test
C15 and C18 Petrolem Generator Set Engines Wiring Information
C280-12 and C280–16 Marine Engines Camshaft - Remove
3512B Marine Auxiliary Engine Product Storage
C9 Engines for Motor Graders Configuration Parameters
C11 and C13 Engines and 14M and 16M Motor Graders Cat Data Link - Test
3512B Marine Auxiliary Engine Refill Capacities and Recommendations
C13 Engine Cylinder Liner - Remove
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.