816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Caterpillar


MID 081 - CID 1402 - FMI 05

Usage:

814F II BXG
Conditions Which Generate This Code:


Illustration 1g01302627

Schematic of the Clutch Solenoid "2 - Forward"

This diagnostic code is associated with the Clutch Solenoid "2 - Forward". The FMI 05 means that the ECM has determined that the current is below normal.

The possible causes of this diagnostic code are listed below:

  • The solenoid energizer circuit of the modulating valve is open.

  • The return circuit of the modulating valve is open.

  • The ECM has failed. This is unlikely.

Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1402 FMI 05 is active before performing this procedure.

Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.

System Response:

When this diagnostic code is active, the ECM will turn off the current to the failed solenoid.

Test Step 1. CHECK THE SOLENOID

  1. Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.

  1. Disconnect the solenoid with the active diagnostic code from the machine harness.

  1. At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire 752-YL) to contact 2 (wire 975-WH).

  1. Observe the status of the CID 1402 FMI 05.

Expected Result:

The CID 1402 FMI 05 remains active. The FMI has not changed and the "05" is still active.

Results:

  • YES - The diagnostic code remains active. The jumper wire does not affect the diagnostic code. Proceed to Test Step 2.

  • NO - The diagnostic is no longer active. The solenoid has failed.

    Repair: The solenoid has failed. Repeat this Test Step "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid. Verify that the new solenoid corrects the problem.

    STOP

Test Step 2. CHECK THE HARNESS FOR AN OPEN

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. Disconnect the machine harness connector(s) from the ECM.

  1. The jumper wire that was installed in the previous test remains in place.

  1. At the machine harness connector, measure the resistance from signal contact J1-11 (wire 752-YL) to contact J1-7 (wire 975-WH).

Expected Result:

The resistance is less than 5.0 ohms.

Results:

  • OK - The resistance is less than 5.0 ohms. The machine harness is correct. Proceed to Test Step 3.

  • NOT OK - The resistance is greater than 5000 ohms. The resistance measurement is not correct. There is an open circuit in the machine harness.

    Repair: The open is in wire 752-YL or in wire 975-WH of the machine harness. Repair the machine harness or replace the machine harness.

    STOP

Test Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS

  1. Inspect the contacts of the harness connectors and clean the harness connectors.

  1. Reconnect all harness connectors.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Operate the machine.

  1. Check the status of the CID 1402 FMI 05.

Expected Result:

The CID 1402 FMI 05 is active.

Results:

  • YES - The CID 1402 FMI 05 is active. The diagnostic code has not been corrected. The ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".

    STOP

  • NO - The CID 1402 FMI 05 is not active. The diagnostic code does not exist at this time.

    Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.

    STOP

Caterpillar Information System:

816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1402 - FMI 03
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes Input High Error IQAN XP2 A1-37
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes Input High Error IQAN XP2 A1-33
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes Input High Error IQAN XP2 A1-31
2006/09/04 Analysis Has Shown the 185-1046 Fan Spider As Functions Properly {1356}
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1401 - FMI 06
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1401 - FMI 05
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1401 - FMI 03
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes Input High Error IQAN XP2 A1-25
Instructions for Updating the AccuGrade® System From MS980C GPS Receivers to MS990C GPS Receivers{7220} Instructions for Updating the AccuGrade® System From MS980C GPS Receivers to MS990C GPS Receivers{7220}
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes Input High Error IQAN XP2 A1-23
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 0668 - FMI 02
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes Input High Error IQAN XP2 A1-39
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1402 - FMI 06
246C, 256C, 262C and 272C Skid Steer Loaders Tire Inflation - Check
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1403 - FMI 03
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1403 - FMI 05
793D Off-Highway Truck/Tractor Piston Motor (Rear Axle Lubrication) - Remove
793D Off-Highway Truck/Tractor Piston Motor (Rear Axle Lubrication) - Install
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes Output High IQAN XT2 A0-33
16M Motor Grader Plate Locations and Film Locations
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1403 - FMI 06
Load Haul Dumps Machines , and Underground Articulated TrucksAutomatic Lubrication System Pressure Reducing Valve - Test and Adjust
Emission Control System for Load Haul Dump Machines and Underground Articulated Trucks Diesel Particulate Filter - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.