Alternator Belt - Remove and Install - Engines With an Automatic Belt Tensioner
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 锁销 Ø 8 mm * 85 mm |
1 |
- 如果发动机配有风扇护罩,卸下该风扇护罩。
Show/hide table
图 1 g01260739 典型实例 - 将适当的方形驱动工具安装到张紧装置 ( 3) 的孔 (X) 中。 从发动机前部,顺时针方向转动工具。
- 将工具 (A) 插入孔 ( Y) 中。 释放方形驱动工具上的压力。
- 卸下交流发电机传动带 ( 1)。
注: 如果还要继续使用传动带,标出传动带的旋向。
- 从发动机前部,顺时针方向转动方形驱动工具。 释放在工具 (A) 上的压力。 从孔 (Y) 上卸下工具 ( A)。
- 释放方形驱动工具上的压力,从孔 ( X) 上卸下工具。
- 如有必要,按照步骤 7.a 和步骤 7.b 以从安装支架 ( 2) 卸下张紧装置 (3)。
- 卸下将张紧装置 ( 3) 固定在安装支架 ( 2) 上的螺栓 (4)。
- 从安装支架 (2) 上卸下张紧装置 ( 3)。
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 锁销 Ø 8 mm * 85 mm |
1 |
- 如果先前已卸下张紧装置,按照步骤 1.a 至步骤 1.c 安装张紧装置。
- 将张紧装置 (3) 后面的定位销与安装支架 ( 2) 中的孔对齐。
- 将张紧装置 (3)安装到安装支架 ( 2) 上。
- 安装螺栓 (4)。 将螺栓拧紧至扭矩
45 N·m (33 lb ft) 。
- 将适当的方形驱动工具安装到张紧装置 ( 1) 的孔 (X) 中。 从发动机前部,顺时针方向转动工具。
- 将工具 (A) 插入孔 ( Y) 中。 释放方形驱动工具上的压力。
- 安装交流发电机传动带 ( 1)。 确保交流发电机传动带以皮带轮 ( 5) 为中心。 应将旧交流发电机传动带按原旋向安装。
注: 交流发电机传动带上的楔必须位于所有皮带轮的楔槽中。
- 从发动机前部,顺时针方向转动方形驱动工具。 释放在工具 (A) 上的压力。 从孔 (Y) 上卸下工具 ( A)。
- 释放方形驱动工具上的压力,直到交流发电机传动带紧固为止。 从孔 (X) 上卸下工具。
注: 张紧装置应在标称位置。
- 如果发动机配有风扇护罩,安装该风扇护罩。
Show/hide table
图 2 | g01270907 |
典型实例 |
Caterpillar Information System:
C4.4 Industrial Engine Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Air Compressor - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Thermistor (Controls Cabinet)
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Storage
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Vacuum Pump Startup - Required Procedure After Extended Storage
3618 Engine Product Lifting
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Power Supply PWAs
2006/06/05 207-5034 Stud Tensioner Tool Gp and 191-5320 Stud Tensioner Tool Gp Require Different Hydraulic Pressures {0701, 0703, 0705, 1100, 1200}
2006/06/01 Replacing Lifters for the Unit Injectors {1209, 1290}
C4.4 Industrial Engine Balancer - Install
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove
C4.4 Industrial Engine Balancer - Remove
C4.4 Industrial Engine Boost Pressure Sensor - Remove and Install
C4.4 Industrial Engine Camshaft - Remove and Install
C4.4 Industrial Engine Camshaft Bearings - Remove and Install
C4.4 Industrial Engine Camshaft Gear - Remove and Install
C4.4 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C4.4 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C4.4 Industrial Engine Coolant Temperature Sensor - Remove and Install
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Filtered Breather
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Unfiltered Breather