Alternator - Install - Engines With an Automatic Belt Tensioner
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 如有必要,将皮带轮 ( 8) 和螺母 (7) 安装到交流发电机 ( 3) 上。 使用六角板手固定交流发电机的轴。 使用带曲柄的梅花扳手(套筒扳手)拧紧螺母 ( 7)。
注: 不同类型交流发电机的螺母尺寸不同。 确保使用适合螺母的正确扭矩值。
拧紧 M16 和 M17 螺母至扭矩
80 N·m (59 lb ft) 。 拧紧 5/8 英寸 - 18 UNF 螺母至扭矩102 N·m (75 lb ft) 。 - 将交流发电机 (3) 放置在交流发电机安装支架 ( 4) 上。
- 将螺栓 (6) 安装到交流发电机 ( 3) 上。 将垫圈 (2) 和螺母 ( 1) 安装到螺栓 (6) 上。
- 将螺栓 (5) 安装到交流发电机 ( 3) 上。
- 拧紧螺母 (1) 和螺栓 ( 5) 至扭矩
22 N·m (16 lb ft) 。 - 将配线线束组件连接到交流发电机 ( 3) 上。
- 安装交流发电机皮带。 请参阅拆解和组装交流发电机传送带 , "- 拆卸和安装" 。
- 将蓄电池断路开关转到 接通位置。
Show/hide table
图 1 | g01271317 |
典型实例 |
Caterpillar Information System:
C4.4 Industrial Engine Air Compressor - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Thermistor (Controls Cabinet)
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Storage
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Vacuum Pump Startup - Required Procedure After Extended Storage
3618 Engine Product Lifting
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Power Supply PWAs
2006/06/05 207-5034 Stud Tensioner Tool Gp and 191-5320 Stud Tensioner Tool Gp Require Different Hydraulic Pressures {0701, 0703, 0705, 1100, 1200}
2006/06/01 Replacing Lifters for the Unit Injectors {1209, 1290}
2006/06/12 Replacing Lifters for the Unit Injectors {1209, 1290}
G3600 Engines Cylinder Block
3612 and 3616 Engines Flexible Coupling
C280 Marine Auxiliary Engines Diagnostic Code List
C4.4 Industrial Engine Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator Belt - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Balancer - Install
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove
C4.4 Industrial Engine Balancer - Remove
C4.4 Industrial Engine Boost Pressure Sensor - Remove and Install
C4.4 Industrial Engine Camshaft - Remove and Install
C4.4 Industrial Engine Camshaft Bearings - Remove and Install
C4.4 Industrial Engine Camshaft Gear - Remove and Install
C4.4 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position