Camshaft - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | FT-2730 | 挂钩 | 12 |
B | 8T-2998 | 润滑剂 | - |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 1 | g01032349 |
- 用工具 (B) 与清洁的发动机机油的 50/50 混合物润滑凸轮轴凸轮和气门挺杆孔。 在凸轮轴轴承轴颈上涂抹清洁的发动机机油。 小心将凸轮轴 (5) 安装在缸体中。
Show/hide table
图 2 g01032348 Show/hide table注意 安装凸轮轴时,确保 1 号缸位于压缩行程的上止点,并且正时螺栓安装在飞轮里。 凸轮轴正时是非常重要的。 凸轮轴驱动齿轮上的正时标记必须对准惰轮上的正时标记。 更多信息,请参考技术规格手册。
- 确保对齐凸轮轴齿轮 (1) 与惰轮齿轮 (2) 上的正时标记。
- 安装止推板 (4) 和螺栓 (3)。
- 磨损的凸轮轴最大容许端隙为
0.46 mm (0.018 in) 。 新凸轮轴最大容许端隙为0.13 ± 0.08 mm (0.005 ± 0.003 in) 。 - 使用工具 (A),将气门挺杆在缸体中放置到位。
- 标定转速/正时传感器。 请参阅故障诊断与排除, "发动机转速 / 正时传感器 - 标定"。
Show/hide table
注意 |
---|
拆卸或安装凸轮轴时不要损坏凸轮或轴承。 |
注: 在凸轮轴安装过程中,应向两个方向转动凸轮轴,以防凸轮轴轴承孔粘连。
结束:
- 安装前盖。 请参阅拆解和组装, "前盖 - 拆卸和安装"。
- 安装摇臂和摇臂轴。 请参阅拆解和组装, "摇臂和轴 - 安装"。
Caterpillar Information System:
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Remote Notification - Setup
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Emergency Power Off - Reset
C9 Engine for Caterpillar Built Machines Camshaft - Remove
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Cable Landing (Maintenance Bypass Cabinet)
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Oil Sample - Obtain
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Transformer (Maintenance Bypass Cabinet)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Time Delay Relay
2006/06/01 New Connecting Rod and Main Bearings {1203, 1218, 1230}
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Remote Input/Output Dry Contact - Setup
2006/05/29 Radiator pedestal on 1104C-TAG engines: Smaller engine mounting holes for improved accuracy of the fan position in the radiator cowl. {1353}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Maintenance Power Supply PWA
C7 and C9 On-Highway Engines Engine Monitoring Parameters
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Circuit Breaker (Maintenance Bypass Cabinet)
TA22-4WD Agricultural Transmission Capacities (Refill)
2006/05/22 Revised Product Support Update {0374}
C4.4 Industrial Engine Alternator - Test
C4.4 Industrial Engine Crankshaft Pulley - Check
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Modem - Configure
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys General Information (Input/Output Cabinet)
C4.4 Industrial Engine V-Belt - Test
797B Off-Highway Truck Steering System Steering Accumulator - Test and Charge
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Log File - Retrieve
CX35 On-Highway Transmission Lubricant Viscosities
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Firmware - Update