UPS View Commands and Hot Keys
Show/hide table
| Event Type | ||
| Code | Type | Color |
| A | Alarm | Red |
| N | Notice | Yellow |
| L | Log | Green |
Show/hide table
| UPS Status | |
| Code | Status |
| A | AVR |
| B | Bypass |
| D | Discharge |
| NC | No Change |
| S | Shutdown |
| O | Online |
Note: The UPS will remain online as long as there are enough functioning flywheels to support the load. Therefore, any notice or alarm from a flywheel may not result in a UPS state change.
Show/hide table
| UPS Command Table | ||
| Name | Hotkey | Password Level |
| Report CAN Reprogramming Status | ? | Service |
| Enable Reporting of Startup Errors | \ | Service |
| Service Report Param. values that change when on genset | Alt-3 | Service |
| Report Password Seed and Serial Number | Alt-F | None |
| Report AVR Demand FPGA Reading | Alt-G | Service |
| Autostart to Inverters On | Alt-I | Service |
| Autostart to Pre-Charge | Alt-P | Service |
| Report Telemetry and Status Registers | Alt-T | Service |
| Report B to Ground Voltage | Alt-U | Service |
| Clear Digital Acq. Capture Lock | Alt-V | Service |
| Toggle Discharge Walk in to Input VAC | Alt-W | Service |
| Upload Digital Acq. Capture Data | Alt-X | Service |
| Report 200 Bytes of Digital Acq. Capture | Alt-Y | None |
| Report Non-60 Hz default Op Params | Alt-Z | None |
| Enter Bypass Mode | Control-B | User |
| Resend Cal Prompt | Control-C | Service |
| Erase Event Log | Control-E | Service |
| Report IGBT Currents | Control-G | None |
| Load default 60 Hz Op Params -> Flash | Control-I | Service |
| Report Diagnostic data | Control-J | None |
| Load default Cal Factors -> SRAM | Control-K | Service |
| Enter Online Mode | Control-O | User |
| Reset the Processor | Control-R | Service |
| Report stack size | Control-T | Service |
| Report DGL Comm. debug buffer | Control-X | None |
| Report current Op Param values | Control-Z | None |
| Clear Discharge Counter | Menu Only | Service |
| Clear Uptime Counters | Menu Only | Service |
| Download Trace Buffer | Menu Only | None |
| Erase Trace Buffer | Menu Only | Service |
| Generate a Test Alarm | Menu Only | Service |
| Generate a Test Notice | Menu Only | Service |
| Load default 50 Hz Op Params -> Flash | Menu Only | Service |
| Load restricted default Params -> Flash | Menu Only | Service |
| Program the ESS with Defaults | Menu Only | Service |
| Report HVI EEPROM | Menu Only | None |
| Report RTC time skew | Menu Only | Service |
| Report Uptime counters | Menu Only | None |
| Toggle Enabling of Debug messages | Menu Only | Service |
| Write Defaults to HVI EEPROM | Menu Only | Service |
| Enable Reporting of startup errors | \ | None |
| FS Deenergize | Alt-D | Service |
| Report Password Seed and Serial Number | Alt-F | None |
| FS Precharge | Alt-P | Service |
| Restart both Flywheels | Alt-R | Service |
| Spin down the currently selected Flywheel | Alt-S | Service |
| Shut down the currently selected Flywheel | Alt-X | Service |
| Report Op Params that are not defaults | Alt-Z | None |
| Force Nonstandard Preheat | Control-^ | Service |
| Resend Calibration Prompt for current FW | Control-C | Service |
| Toggle the currently selected FW | Control-F | Service |
| Report Skiip currents from FPGA | Control-G | None |
| Load default Op Params into flash | Control-I | Service |
| Report current diagnostic information | Control-J | None |
| Load Default Cal Factors into SRAM | Control-K | Service |
| Enter Online Mode | Control-O | User |
| Reset The Microprocessor | Control-R | Service |
| Enter Shutdown Mode | Control-S | Service |
| Report Stack Info | Control-T | Service |
| Reset the DSP | Control-U | Service |
| Brake both Flywheels | Control-X | Service |
| Report Setpts and Op Params From Flash | Control-Z | None |
| Calibrate RPS for current FW | Menu Only | Service |
| Clear Discharge Counter | Menu Only | Service |
| Clear Uptime Meter | Menu Only | Service |
| Erase Trace Buffer | Menu Only | Service |
| Generate a Bunch of Events | Menu Only | Service |
| Generate a Test Alarm | Menu Only | Service |
| Generate a Test Notice | Menu Only | Service |
| Load Restricted Op Params | Menu Only | Service |
| Reload Cal Factor/Op Params from Flash | Menu Only | Service |
| Select FWA | Menu Only | Service |
| Select FWB | Menu Only | Service |
| Toggle Debug messages | Menu Only | User |
| Report Comm. Error counters | ' | None |
| Report Pager State | = | None |
| Report System Event Log | Control-D | None |
| (UI) Report Command Hotkeys | Control-H | None |
| Report Program Versions | Control-N | None |
| (UI) Clear View Password | Control-P | User |
| Reset Modem NVRAM | Control-Q | Service |
| Toggle Modem On/Off Hook | Control-W | Service |
| Report Modem Configuration | Control-Y | None |
| Cancel Ethernet Remote Access | Menu Only | Master |
| Cancel Modem Remote Access | Menu Only | Master |
| Cancel Paging | Menu Only | User |
| Delete Supervisor Logfile | Menu Only | Service |
| Enable All Summary Tiles | Menu Only | User |
| Generate UI Test event | Menu Only | Service |
| Load empty Device Messages from File | Menu Only | Service |
| Reboot the UI | Menu Only | Service |
| Reboot the whole system | Menu Only | Service |
| Report Active Events | Menu Only | None |
| Report Modbus Registers | Menu Only | None |
| Report Monitoring connections | Menu Only | None |
| Report Supervisor Logfile | Menu Only | None |
| Report Unacked Events | Menu Only | None |
Caterpillar Information System:
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Messages
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Graphical User Interface Messages
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys UPS Messages
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Operating Parameters
C9 Engine for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Current Transformers (Primary, Secondary)
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Voltage - Calibrate
C9 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold - Remove
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold - Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Transformer (T12 to T16 )
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Controller Board Battery - Replace
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Fan (4 Wire Transformer Cabinet)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys External Source Sync PWA (4 Wire Transformer Cabinet)
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission - Assemble
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies General Information (Cabinet Hardware)
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Door
C280 Marine Auxiliary Engines System Overview
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Door Pull and Retaining Ring
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Door Latch
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Output Current - Calibrate
2006/05/22 Wiring for the Coolant Level Switches and the Coolant Level Sensors {7422}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys General Information (Maintenance Bypass Cabinet)
C7 and C9 On-highway Engines Engine Oil and Filter - Change