Fan (Input/Output Cabinet)
Show/hide table
| |
| Illustration 1 | g01271038 |
|
Location of the Fans in the I/O Cabinet (1) Fans | |
There are three fans that are located at the top of the I/O cabinet. Refer to Illustration 1 for the location of the fans in the I/O cabinet.
Refer to Systems Operation, Testing and Adjusting, RENR9988, "Internal Component Preremoval Steps (Input/Output Cabinet)" in order to shut down the system and gain access to internal components.
- Refer to Illustration 2 for removal of the fan assembly.
- Remove the two screws (2) that hold the flap (3) to the cabinet.
- Remove the six screws (4) that hold the fan to the cabinet.
- Remove the flap (3). Remove the screen (5).
- Remove the fan unit (6) from the cabinet.
- Disconnect the fan power/sense cable (7) that is located on the left side of the unit.
Show/hide table
| |
| Illustration 2 | g01271036 |
|
Fan Assembly (2) Flap Screws (3) Flap (4) Screw (5) Screen (6) Fan Unit (7) Fan Power/Sense Cable (8) Front of Cabinet | |
- Refer to Illustration 2 for installation of the fan assembly.
- Connect the fan power/sense cable (7) into the left side of the fan unit.
- Position the fan unit (6) into the cabinet.
- Place the fan screen (5) over the fan unit. Attach the fan screen (5) with six screws (4).
- Place the flap for the fan (3) over the screen. Attach the flap for the fan (3) to the cabinet with the two screws (2).
Caterpillar Information System:
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Isolation Switches
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Fan Transformer
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Fuse (Input/Output Cabinet)
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Internal Component Preremoval Steps (Input/Output Cabinet)
2006/07/10 New Parts are Available for Engines that use Heavy Duty Air Cleaners {1051, 1316, 1317}
TH48-E70 Petroleum Transmission Plate Locations and Film Locations
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Bringing UPS Online
3412E and C30 Marine Engines Cooling System Coolant Level - Check
C4.4 Industrial Engine Fuel System - Prime
2006/05/15 New Crankshaft Front Seal {1160}
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Modem (SMS Bypass Cabinet)
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Gen Set Module Circuit Breaker
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies External Source Sync Relay and Terminal Block
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Gen Set Module Circuit Breaker (Input/Output Cabinet)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Transfer to Bypass Mode
Troubleshooting the Fuel Injection System For 3054 and 3056 Engines {1251, 1252} Troubleshooting the Fuel Injection System For 3054 and 3056 Engines {1251, 1252}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Transfer to Online Mode
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Preheat Modes
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Service Tools
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys General Information (4 Wire Output Cabinet)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Maintenance
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Internal Component Preremoval Steps (4 Wire Output Cabinet)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Circuit Breaker (K8)
VR6 Or K65-12B Voltage Regulators Require An External Jumper Wire When Used With A Permanent Magnet Generator{4467} VR6 Or K65-12B Voltage Regulators Require An External Jumper Wire When Used With A Permanent Magnet Generator{4467}