TA19-M2WD and TA19-M4WD Agricultural Transmissions Caterpillar


Relief Valve (Transmission Main) - Assemble

Usage:

TA19-M2WD T2Z

Assembly Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
1P-1853  Retaining Ring Pliers 

Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.

Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

Dispose of all fluids according to local regulations and mandates.




    Illustration 1g01209518

    ------ WARNING! ------

    Personal injury can result from being struck by parts propelled by a released spring force.

    Make sure to wear all necessary protective equipment.

    Follow the recommended procedure and use all recommended tooling to release the spring force.


  1. Install ball (12), spring (13), and retainer (14). Use Tooling (A) in order to install retaining ring (15).

  2. Install slug (16).


    Illustration 2g01209507

  3. Install spool assembly (11).


    Illustration 3g01209506

  4. Install spring (10), O-ring seal (9), and load piston (8).


    Illustration 4g01209465

    ------ WARNING! ------

    Personal injury can result from being struck by parts propelled by a released spring force.

    Make sure to wear all necessary protective equipment.

    Follow the recommended procedure and use all recommended tooling to release the spring force.


  5. Install adjustment screw (7) to the original location. Install cover (5) and bolts (6). Tighten bolts (6) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).


    Illustration 5g01209450

  6. Install O-ring seal (4).


    Illustration 6g01209441

  7. Install cover (3) and bolts (2). Tighten bolts (2) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).


    Illustration 7g01209440

  8. Install O-ring seal (1).

End By:

  1. Install the relief valve. Refer to Disassembly and Assembly, "Relief Valve (Transmission Main) - Install".

Caterpillar Information System:

C4.4 Industrial Engine Fuel Injection Timing - Check
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines E360 Low Engine Oil Pressure
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Overload Relay (SMS Bypass Cabinet)
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Circuit Breaker (SMS Bypass Cabinet)
TA22 Transmission Temperature Sensor (Transmission Oil) - Remove and Install
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Contactor (SMS Bypass Cabinet)
TA22 Transmission Relief Valve (Transmission Main) - Install
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Vacuum Pump Oil - Change
TA22 Transmission Relief Valve (Transmission Main) - Remove
TA22 Transmission Speed Sensor (Transmission) - Install
G3406 and G3412 Generator Sets Starting the Engine
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Transformer (SMS Bypass Cabinet)
TA19-M2WD and TA19-M4WD Agricultural Transmissions Relief Valve (Transmission Main) - Disassemble
TA22 Transmission Modulating Valve (Transmission Clutch) - Remove and Install
C175-16 and C175-20 Generator Set Engines Exhaust Fitting
TA22 Transmission Pressure Sensor (Charge Pump) - Remove and Install
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Static Drain - Install
TA22 Transmission Transmission - Disassemble
TA22 Transmission Transmission - Assemble
TA22 Transmission Pump Drive - Remove
TA22 Transmission Pump Drive - Install
TH48-E70 Petroleum Transmission Torque Converter and Transmission Oil Level - Check
TH48-E70 Petroleum Transmission Torque Converter and Transmission Oil - Change
C175-16 Locomotive Engine Exhaust Fitting
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.