TA22 Transmission Caterpillar


Speed Sensor (Transmission) - Install

Usage:

TA22-M4WD T4W


Installation Procedure

Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.

Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.

Input Speed Sensor




    Illustration 1g01269299

  1. Install speed sensor (2) and bolt (3). Connect harness assembly (1) .

Output Speed Sensors




    Illustration 2g01269246

  1. Install speed sensor (1) and bolt (4). Connect harness assembly (2). Repeat for the remaining speed sensor (3) .

Caterpillar Information System:

G3406 and G3412 Generator Sets Starting the Engine
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Transformer (SMS Bypass Cabinet)
TA22 Transmission Speed Sensor (Transmission) - Remove
C9 Marine Engines and C9 Marine Generator Sets Unit Injector Hydraulic Pump
3500C Marine Engines Turbocharger
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Bypass Static Switch (SMS Bypass Cabinet)
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission - Disassemble
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Bypass Contactor and Capacitor
C13 and C15 On-Highway Engines Fuel System Secondary Filter - Replace
SPF343 and SPF343C Trailer Mounted Pumpers Emergency Stopping
3500B Industrial Engines with the ADEM 3 Electronic Control Module Starting Motor System
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Maintenance Bypass Disconnect Switch - SMS Bypass Cabinet
TA22 Transmission Relief Valve (Transmission Main) - Remove
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Vacuum Pump Oil - Change
TA22 Transmission Relief Valve (Transmission Main) - Install
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Contactor (SMS Bypass Cabinet)
TA22 Transmission Temperature Sensor (Transmission Oil) - Remove and Install
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Circuit Breaker (SMS Bypass Cabinet)
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Overload Relay (SMS Bypass Cabinet)
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines E360 Low Engine Oil Pressure
C4.4 Industrial Engine Fuel Injection Timing - Check
TA19-M2WD and TA19-M4WD Agricultural Transmissions Relief Valve (Transmission Main) - Assemble
TA19-M2WD and TA19-M4WD Agricultural Transmissions Relief Valve (Transmission Main) - Disassemble
TA22 Transmission Modulating Valve (Transmission Clutch) - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.