C13 and C15 On-Highway Engines Caterpillar


Fuel System Secondary Filter - Replace

Usage:

C15 B5R


------ WARNING! ------

渗漏或溅溢到热表面或电气部件上的燃油会引起失火。 为防止可能的伤害,当更换燃油滤清器或油水分离器滤芯时,要将起动开关断开。 应立即将溅溢的燃油清除干净。



注意

不要让脏物进入燃油系统。 彻底清洁要拆开的燃油系统部件的周围区域。 在所有拆开的燃油系统部件上安放适当的盖。



    注意

    在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。

    有关适于收集和盛放 Cat 产品油液的工具和用品,请参阅专门出版物, NENG2500, "Cat 代理商维修工具目录"或专门出版物, PECJ0003, "Cat 车间用品和工具目录"。

    按照本地法规和要求处置所有油液。


  1. 关闭发动机。 把点火开关转到停机 (OFF)位置或断开蓄电池。 详细资料请参考操作和保养手册, "蓄电池或蓄电池电缆 - 断开"专题(保养部分)。 关断燃油供油阀(如有配备)。


    图 1g01269066
    (1) 排气螺钉接头

  2. 为了释放燃油压力,逆时针转动排气螺钉接头整三圈。 不要拆下接头。

  3. 拆下并废弃已经用过的燃油滤清器。

  4. 关闭排气螺钉接头。 有关正确的扭矩,请参阅专门出版物, SENR3130, "扭矩技术参数"。

  5. 清洁燃油滤清器底座的垫圈密封表面。 确保清除所有旧密封垫。 在新的燃油滤清器垫圈上涂抹一层清洁的柴油。


    注意

    卡特彼勒要求使用一个高效绝对值为 4 微米 (c) 燃油细滤器。



    注意

    安装前不要注满燃油细滤器。 这些燃油将不被过滤并可能受到污染。 污染的燃油会加速燃油系统零件的磨损。


  6. 安装新燃油滤清器。 把燃油滤清器旋装到燃油滤清器底座上,直到垫圈接触到底座。 滤清器安装的说明打印在每个卡特彼勒旋装式滤清器的侧面上。 对于非卡特彼勒滤清器,请参阅滤清器供应商提供的安装说明。

  7. 打开燃油箱供油阀。 把点火开关转到接通 (ON)位置或重新连接蓄电池。 打开供油阀(如有配备)。

  8. 充注燃油系统。 有关更多信息,请参考操作和保养手册, "燃油系统 - 充注"专题(保养部分)。 起动发动机,并检查燃油系统有无漏损。


注意

持续盘车不要超过30秒。 再次盘车前,让起动马达先冷却2分钟。


Caterpillar Information System:

SPF343 and SPF343C Trailer Mounted Pumpers Emergency Stopping
3500B Industrial Engines with the ADEM 3 Electronic Control Module Starting Motor System
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Maintenance Bypass Disconnect Switch - SMS Bypass Cabinet
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Vibration Sensor - Calibrate
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Controller PWA (SMS Bypass Cabinet)
3600 Mechanical Unit Injector (MUI) to 3600 Electronic Unit Injector (EUI) Upgrade{1000, 1250} 3600 Mechanical Unit Injector (MUI) to 3600 Electronic Unit Injector (EUI) Upgrade{1000, 1250}
C9 On-highway Engine Engine Oil Filter Base
TA22-4WD Agricultural Transmission Visual Inspection
C4.4 Industrial Engine Finding Top Center Position for No. 1 Piston
TA19-M2WD and TA19-M4WD Agricultural Transmissions Clutch (Front Wheel Assist) - Assemble
3500B Industrial Engines with the ADEM 3 Electronic Control Module Speed Control
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Fuse (SMS Bypass Cabinet)
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Bypass Contactor and Capacitor
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission - Disassemble
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Bypass Static Switch (SMS Bypass Cabinet)
3500C Marine Engines Turbocharger
C9 Marine Engines and C9 Marine Generator Sets Unit Injector Hydraulic Pump
TA22 Transmission Speed Sensor (Transmission) - Remove
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Transformer (SMS Bypass Cabinet)
G3406 and G3412 Generator Sets Starting the Engine
TA22 Transmission Speed Sensor (Transmission) - Install
TA22 Transmission Relief Valve (Transmission Main) - Remove
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Vacuum Pump Oil - Change
TA22 Transmission Relief Valve (Transmission Main) - Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.