1. Home
  2. Caterpillar
  3. Disassembly and Assembly
  4. #i02532031

TA19-M2WD and TA19-M4WD Agricultural Transmissions Caterpillar


Pump Drive - Install

Usage:

TA19-M2WD T2Z

Installation Procedure

Show/hide table
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     138-7575     Link Brackets     4    
B     1U-9202     Lever Puller Hoist     1    
C     1P-2420     Transmission Repair Stand     1    
F     1U-8846     Gasket Sealant     -    
    Show/hide table

    Illustration 1g01266709

  1. Install bearing (36) into gear (34) .
    Show/hide table

    Illustration 2g01266697

  1. Install thrust discs (35). Install gear (34) .
    Show/hide table

    Illustration 3g01265950

  1. Install shaft (33). Install bolt (32) .
    Show/hide table

    Illustration 4g01266612

  1. Install O-ring seal (31), cover (30), and bolts (29) .
    Show/hide table

    Illustration 5g01266763

  1. Raise the temperature of bearings (28). Install bearings (28) onto gear (26) .
    Show/hide table

    Illustration 6g01265924

  1. Install O-ring seal (27) and gear (26) onto adapter (24) .
    Show/hide table

    Illustration 7g01266820

  1. Install gear (26) and adapter (24). Install bolts (25) .
    Show/hide table

    Illustration 8g01265910

  1. Use Tooling (A), Tooling (B), and a suitable lifting device in order to reposition case assembly (23). The weight of case assembly (23) is approximately 365 kg (800 lb). Apply Tooling (F) to case assembly (23). Install case assembly (23) .
    Show/hide table

    Illustration 9g01265880

  1. Install tube assembly (22) .
    Show/hide table

    Illustration 10g01265863

  1. Install tube assembly (21). Install bolt (20) .

  1. Install shims (19) and retainer (18). Install bolts (17) .

    Note: If new bearings are installed, check the end play of the shaft assembly. Refer to Disassembly and Assembly, "Transmission - Assemble".

  1. Repeat Step 11 for the other retainers.
    Show/hide table

    Illustration 11g01265831

  1. Use two people in order to install gear assembly (16). The weight of gear assembly (16) is approximately 30 kg (70 lb).
    Show/hide table

    Illustration 12g01265829

  1. Use two people in order to install gear (15). The weight of gear (15) is approximately 23 kg (50 lb). Install retainer (14) and bolt (13) .
    Show/hide table

    Illustration 13g01265805

  1. Apply Tooling (F) to cover assembly (9) .

  1. Use Tooling (A) and a suitable lifting device in order to install cover assembly (9). The weight of cover assembly (9) is approximately 60 kg (130 lb).

  1. Check the end play of the shaft assembly. Refer to Disassembly and Assembly, "Transmission - Assemble".

  1. Position harness assembly (12) .

  1. Install bracket assemblies (11) and bolts (10) .
    Show/hide table

    Illustration 14g01265795

  1. Install O-ring seal (5). Install yoke (8), retainer (7), and bolt (6) .
    Show/hide table

    Illustration 15g01265775
    Show/hide table

    Illustration 16g01265774

  1. Use Tooling (A), Tooling (B), and a suitable lifting device in order to reposition transmission (4). The weight of transmission (4) is approximately 1315 kg (2900 lb).
    Show/hide table

    Illustration 17g01265765

  1. Install Electronic Control Module (3) and bolts (2) .

  1. Connect harness assemblies (1) .

End By: Install the input speed sensor. Refer to Disassembly and Assembly, "Speed Sensor (Transmission) - Install".

Caterpillar Information System:

TH55FT-E70 and TH55FT-E90 Transmissions Lubricant Viscosities
C9 On-highway Engine Cylinder Block Cover Group
C32 Marine Engine Cooling System Coolant (ELC) - Change
C32 Marine Engine Cooling System Coolant (DEAC) - Change
C9 On-highway Engine Jacket Water Heater
C9 Marine Engines and C9 Marine Generator Sets Boost Pressure Sensor
C15 On-Highway Engine Electronic Control System Components
C13 and C15 On-Highway Engines Engine Operation
C9 On-highway Engine Air Compressor
3044C Industrial Engine Refill Capacities and Recommendations
3500B Industrial Engines with the ADEM 3 Electronic Control Module Permanent Timing Calibration Sensor
C4.4 Industrial Engine Electronic Control System
C13 Engine Camshaft Position Sensor - Remove and Install
C13 Engine Engine Oil Pressure Sensor - Remove and Install
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Operational Modes
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Flywheel Preheat Modes
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Front Panel Overview
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Additional UPS Concepts
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Service Connections
C13 Engine Engine Oil Pressure Sensor - Remove and Install - Intake Valve Actuator
C4.4 Industrial Engine Power Sources
C13 and C15 On-Highway Engines Monitoring System - Dash Lamps and Controls for the Aftertreatment Regeneration Device (ARD)
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies MMU Messages
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies MMU Master Messages
Back to top
Contacts My AVS
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.