C13 Engine Caterpillar


Fuel Temperature Sensor - Remove and Install

Usage:

C13 LEE

Removal Procedure

Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.

Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.

Dispose of all fluids according to local regulations and mandates.





    Illustration 1g01266492

  1. Disconnect harness assembly (1). Remove fuel temperature sensor (2) .

Installation Procedure

Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.

Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.

Dispose of all fluids according to local regulations and mandates.





    Illustration 2g01266492

  1. Install fuel temperature sensor (2). Tighten fuel temperature sensor (2) to a torque of 20 ± 5 N·m (15 ± 4 lb ft). Connect harness assembly (1) .

Caterpillar Information System:

Mechanical Application and Installation Guide for TH48-E70 Petroleum Transmissions{3030, 3101} Mechanical Application and Installation Guide for TH48-E70 Petroleum Transmissions{3030, 3101}
C13 Engine Crankshaft Position Sensor - Remove and Install
3500B Industrial Engines with the ADEM 3 Electronic Control Module Overspeed Verify Switch
C7 On-Highway Engine Fuel Pressure Sensor - Remove and Install - Pilot
C9 On-highway Engine Electronic Unit Injector Wiring
C7 On-Highway Engine Fuel Pressure Sensor - Remove and Install - Main
C7 On-Highway Engine Coolant Temperature Sensor - Remove and Install
C7 On-Highway Engine Flywheel Housing - Remove and Install
TH48-E70 Petroleum Transmission Lifting and Tying Down the Transmission
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Configuration
C7 On-Highway Engine Clean Gas Induction Valve - Assemble
C13 Engine Air Compressor - Remove and Install
C4.4 Industrial Engine Electronic Control System
3500B Industrial Engines with the ADEM 3 Electronic Control Module Permanent Timing Calibration Sensor
3044C Industrial Engine Refill Capacities and Recommendations
C9 On-highway Engine Air Compressor
C13 and C15 On-Highway Engines Engine Operation
C15 On-Highway Engine Electronic Control System Components
C9 Marine Engines and C9 Marine Generator Sets Boost Pressure Sensor
C9 On-highway Engine Jacket Water Heater
C32 Marine Engine Cooling System Coolant (DEAC) - Change
C32 Marine Engine Cooling System Coolant (ELC) - Change
C9 On-highway Engine Cylinder Block Cover Group
TH55FT-E70 and TH55FT-E90 Transmissions Lubricant Viscosities
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.