Lifting and Tying Down the Transmission
Show/hide table
| |
| 图 1 | g00103219 |
Show/hide table
| 注意 |
|---|
|
千万不要折弯吊环螺栓和支架。 吊环螺栓和支架只能承受张力负荷。 要记住当支承构件和物体之间的角度小于90°时，吊环螺栓的承载能力变小。 当必须在某一角度搬移部件时，只能使用具有适当额定载荷的连杆支架。 |
较重部件的移动需要起吊机和吊具以保证平衡和安全。 安放起吊机使其方便水平起吊变速箱，并使用可调整的吊梁提升变速箱。 撑杆宽度应足够防止接触变速箱。 所有的支撑件（吊链与钢丝绳）应当彼此平行，并与正在起吊的物体的顶面保持垂直。 改动吊耳或夹紧装置会使吊耳或吊装工具失效。 使用规格合适的吊链、钢丝绳和吊具。
Show/hide table
| |
| 图 2 | g03112776 |
|
TH48-E70 变速箱 (1) 吊耳（四个） | |
- TH48-E70 变速箱和发动机连接器（带干油池）的重量约为
1694 kg (3735 lb) 。 - 图 2 中标出了 TH48-E70 石油变速箱可以接受的起吊点 (1)。 变速箱设计为平放在变速箱底座上。
- 起吊时，请小心操作，避免损坏外部安装部件，如：ECM、电磁阀、导线线束、软管和传感器。
应使用图 2 中所示的后变速箱吊耳来系紧 TH48-E70 石油变速箱的后部。 可在变矩器壳体上使用批准的束带或链条来系紧 TH48-E70 石油变速箱的前部。
Caterpillar Information System:
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Configuration
C7 On-Highway Engine Clean Gas Induction Valve - Assemble
C13 Engine Air Compressor - Remove and Install
3500B Industrial Engines with the ADEM 3 Electronic Control Module Intermediate Speed Switch
C15 On-Highway Engine Fuel Filter Base
2006/07/01 A New Field Service Kit for Alternators is Now Available {1405, 7555}
C13 On-highway Engine Fuel Priming Pump
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Abbreviations and Acronyms
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Overview
C9 Marine Engines and C9 Marine Generator Sets Injection Actuation Pressure Sensor
C7 On-Highway Engine Air Inlet Cover - Remove and Install
2006/08/07 A New Oil Pump for the Hydrax System is Used {1716, 5073}
C7 On-Highway Engine Flywheel Housing - Remove and Install
C7 On-Highway Engine Coolant Temperature Sensor - Remove and Install
C7 On-Highway Engine Fuel Pressure Sensor - Remove and Install - Main
C9 On-highway Engine Electronic Unit Injector Wiring
C7 On-Highway Engine Fuel Pressure Sensor - Remove and Install - Pilot
3500B Industrial Engines with the ADEM 3 Electronic Control Module Overspeed Verify Switch
C13 Engine Crankshaft Position Sensor - Remove and Install
Mechanical Application and Installation Guide for TH48-E70 Petroleum Transmissions{3030, 3101} Mechanical Application and Installation Guide for TH48-E70 Petroleum Transmissions{3030, 3101}
C13 Engine Fuel Temperature Sensor - Remove and Install
C4.4 Industrial Engine Electronic Control System
3500B Industrial Engines with the ADEM 3 Electronic Control Module Permanent Timing Calibration Sensor
3044C Industrial Engine Refill Capacities and Recommendations