Transmission Pump Drive Housing - Remove
Start By:
- Remove the bottom guard for the transmission. Refer to Disassembly and Assembly, "Bottom Guard (Transmission) - Remove".
- Remove the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Implement, Pilot, Steering, Brake) - Remove".
- Remove the transmission oil pump. Refer to Disassembly and Assembly, "Transmission Oil Pump - Remove".
Note: Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
- Remove bolts (1) and disconnect tube assembly (2).
Show/hide table
Illustration 2 g00586264 - Remove bolts (3) and cover assembly (4).
Show/hide table
Illustration 3 g00586267 - Remove bolts (5) and shaft (6) from cover assembly (4).
Show/hide table
Illustration 4 g00586269 - Remove retaining ring (7), gear (8), and bearing (9) from cover assembly (4).
Show/hide table
Illustration 5 g00586271 - Use a suitable press to remove bearing (9) from gear (8).
Show/hide table
Illustration 6 g00586273 - Remove bolts (10) and housing (11).
Show/hide table
Illustration 7 g00586276 - Remove bolts (12) from housing (11) and shaft (13).
Show/hide table
Illustration 8 g00586279 Show/hide tableIllustration 9 g00586280 - Use a suitable press to remove shaft (13), gear (14), spacer (15), and bearing race (16) from housing (11).
Show/hide table
Illustration 10 g00586283 - Remove retaining ring (17), gear (18), and bearing (19) from housing (11).
Show/hide table
Illustration 11 g00586285 - Use a suitable press to remove bearing (19) from gear (18).
Show/hide table
Illustration 1 | g00586263 |
Caterpillar Information System:
D6G Series 2 Track-Type Tractor Power Train Brakes
938H Wheel Loader and IT38H Integrated Toolcarrier Steering System Secondary Steering Pump and Electric Motor
938H and IT38H Wheel Loader and Integrated Tool Carrier Power Train Transmission Oil Pump
2006/05/01 Inspection and/or Repair Procedure to Replace Crankshafts on Machine Engines {1202}
938H Wheel Loader and IT38H Integrated Toolcarrier Steering System Check Valve (Secondary Steering)
D6G Series 2 Track-Type Tractor Power Train Hydraulic Control Mechanism
525C, 535C and 545C Wheel Skidders Machine Systems Hydraulic Tank - Install
525C, 535C and 545C Wheel Skidders Machine Systems Hydraulic Tank - Remove
2006/06/05 New Speed Timing Sensor is Available {1912}
D6G Series 2 Track-Type Tractor Power Train Steering Clutch Hydraulic Control Valve
938H and IT38H Wheel Loader and Integrated Tool Carrier Power Train Temperature Sensor (Torque Converter Oil)
D7R Series II Track-Type Tractor Machine Systems Counterbalance Valve - Install
525C, 535C and 545C Wheel Skidders Power Train Transmission Pump Drive Housing - Install
D7R Series II Track-Type Tractor Machine Systems Piston Motor (Steering) - Remove
2006/04/24 Correction to Specification , "D3C, D4C and D5C Series III Hystat Track-Type Tractor Power" {4350}
D7R Series II Track-Type Tractor Machine Systems Piston Motor (Steering) - Install
D11T, D8T and D9T Track-Type Tractors VIMSTM 3G / Product Link Electronic Control Module (ECM) - Replace
D7R Series II Track-Type Tractor Machine Systems Piston Motor (Steering) - Disassemble
C4.4 Industrial Engine Fuel Injection
D7R Series II Track-Type Tractor Machine Systems Piston Motor (Steering) - Assemble
631G Wheel Tractor-Scraper Power Train Speed Sensor (Transmission) - Assemble
The Breather Hole In 7T-7706 Housing As Is Not Drilled To the Correct Depth{3120} The Breather Hole In 7T-7706 Housing As Is Not Drilled To the Correct Depth{3120}
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Control Manifold (Implement, Steering Pump Margin Relief)
D7G2 Track-Type Tractor Power Train Sequence Relief Valve