Valve Mechanism Cover Base - Remove and Install
Start By:
- Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Disconnect harness assembly (1).
Show/hide table
Illustration 2 g01259577 - Disconnect harness assemblies (2) from the electronic fuel injectors.
Show/hide table
Illustration 3 g01259582 - Disconnect tube assembly (3).
Show/hide table
Illustration 4 g01259651 - Loosen hose clamps (4). Slide hose (5) out of the way. Remove bolt (6) and bracket (7).
Show/hide table
Illustration 5 g01259652 - Remove bolt (8). Remove bracket (9). Remove remaining bolts (8) and remove valve mechanism cover base (10).
Show/hide table
Illustration 1 | g01259575 |
- Install valve mechanism cover base (10). Install bolts (8). Install bracket (9). Install remaining bolt (8).
Show/hide table
Illustration 7 g01212679 - The face of Clips (X) must be parallel to the center line of the crankshaft. Tighten bolts (8) in a numerical sequence to a torque of
27 ± 8 N·m (20 ± 6 lb ft) .Show/hide tableIllustration 8 g01259651 - Install bracket (7) and bolt (6). Slide hose (5) into position. Tighten hose clamps (4).
Show/hide table
Illustration 9 g01259582 - Connect tube assembly (3).
Show/hide table
Illustration 10 g01259577 - Connect harness assemblies (2) to the electronic unit injectors.
Show/hide table
Illustration 11 g01259575 - Connect harness assembly (1).
Show/hide table
Illustration 6 | g01259652 |
End By:
- Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Caterpillar Information System:
2006/04/17 "Tool and Shop Products Guide" by the Cat Service Technology Group (CSTG) Has Been Replaced by Two New Catalogs {0374}
2006/05/01 New Location for the Magneto's Vent {1552}
C7 PETROLEUM Petroleum Engine Cylinder Head - Install
3500B and 3500C Locomotive Engines Start/Run/Stop Switch
2006/04/03 Replacement Criteria for Camshafts {1210}
2006/04/01 Replacement Criteria for Camshafts {1210}
C4.4 Industrial Engine Basic Engine
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Startup (MMS) - Multiple Module System
C7 On-Highway Engine Combustion Head - Remove and Install
C4.4 Industrial Engine Fuel System Secondary Filter - Replace
C7 On-Highway Engine Clean Gas Induction Valve - Install
C15 and C18 Petroleum Generator Sets Generator Lead - Check
C7 PETROLEUM Petroleum Engine Lifter Group - Remove and Install
C4.4 Industrial Engine Walk-Around Inspection
3500B and 3500C Locomotive Engines Throttle Position Sensor
C7 PETROLEUM Petroleum Engine Camshaft - Remove
C4.4 (Mech) Industrial Engine V-Belts - Inspect/Adjust/Replace
C7 PETROLEUM Petroleum Engine Camshaft - Install
2006/05/22 New Water Cooled Exhaust Manifold {1059}
C4.4 Industrial Engine Water Pump - Inspect
C15 On-Highway Engine Rocker Arm and Shaft - Remove
C15 On-Highway Engine Rocker Arm and Shaft - Install
C15 On-Highway Engine Electronic Unit Injector - Remove
C15 On-Highway Engine Electronic Unit Injector - Install