2006/04/03 Caterpillar


Replacement Criteria for Camshafts {1210}

Usage:

3406E 6BR
Generator Set Engines:
3406E (S/N: 5GF1-UP; 9NN1-UP)
Industrial Engine:
3406E (S/N: 6BR1-UP)
Marine Engine:
3406E (S/N: 9WR1-UP)

The guidelines below enable customers to benefit from cost reductions. The cost reductions are made possible through an established reusability of parts and a program for salvaged parts.

Use the publications below in order to determine the following conditions of a camshaft. Determine reusability, repair, or replacement of the camshaft.

  • Guideline For Reusable Parts And Salvage Operations, SEBF8097, "Camshaft Measurement"

  • Guideline For Reusable Parts And Salvage Operations, SEBF8146, "Visual Inspection of Camshaft"

  • Guideline For Reusable Parts And Salvage Operations, SEBU8256, "Visual Inspection of Camshaft and Rocker Arm Rollers Used in 3406E Engines"

  • Special Instruction, REHS1572, "Replacement Criteria for Camshaft in 3406E C15 and C16 Truck Engines"

Caterpillar Information System:

2006/04/01 Replacement Criteria for Camshafts {1210}
C4.4 Industrial Engine Basic Engine
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Startup (MMS) - Multiple Module System
C7 On-Highway Engine Combustion Head - Remove and Install
C4.4 Industrial Engine Fuel System Secondary Filter - Replace
C7 On-Highway Engine Clean Gas Induction Valve - Install
C15 and C18 Petroleum Generator Sets Generator Lead - Check
3500B and 3500C Locomotive Engines Starting Motor System
C7 PETROLEUM Petroleum Engine Cylinder Head - Remove
C4.4 Industrial Engine Fuel System Primary Filter (Water Separator) Element - Replace
Update of the Initial Flash Procedure for the Primary ECM{0785, 7620} Update of the Initial Flash Procedure for the Primary ECM{0785, 7620}
Bench Test Procedure for a CX31 On-Highway Transmission and CX31-P600 Petroleum Transmission {3030, 3073} Bench Test Procedure for a CX31 On-Highway Transmission and CX31-P600 Petroleum Transmission {3030, 3073}
3500B and 3500C Locomotive Engines Start/Run/Stop Switch
C7 PETROLEUM Petroleum Engine Cylinder Head - Install
2006/05/01 New Location for the Magneto's Vent {1552}
2006/04/17 "Tool and Shop Products Guide" by the Cat Service Technology Group (CSTG) Has Been Replaced by Two New Catalogs {0374}
C7 On-Highway Engine Valve Mechanism Cover Base - Remove and Install
C7 PETROLEUM Petroleum Engine Lifter Group - Remove and Install
C4.4 Industrial Engine Walk-Around Inspection
3500B and 3500C Locomotive Engines Throttle Position Sensor
C7 PETROLEUM Petroleum Engine Camshaft - Remove
C4.4 (Mech) Industrial Engine V-Belts - Inspect/Adjust/Replace
C7 PETROLEUM Petroleum Engine Camshaft - Install
2006/05/22 New Water Cooled Exhaust Manifold {1059}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.