Front Frame from Rear Frame - Separate
分离步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 5H-9817     | 液压油箱     | 1     |
9U-5346 | 螺母     | 1     | |
9U-5344 | 拉拔器螺柱     | 1     | |
6V-4035 | 套筒     | 1     | |
3S-6224 | 电动液压泵总成     | 1     | |
B     | 9U-7536     | 起吊台     | 2     |
277-7200 | 电动液压泵总成     | 1     | |
C     | 3S-6224     | 电动液压泵总成     | 1     |
9U-6814 | 拉拔器螺柱     | 1     | |
124-4640 | 套筒     | 1     | |
5P-5212 | 盘     | 1     | |
6V-0014 | 液压油箱     | 1     | |
9U-6810 | 螺母     | 1     | |
D     | 3S-6224     | 电动液压泵总成     | 1     |
9U-6814 | 拉拔器螺柱     | 1     | |
5P-5212 | 盘     | 1     | |
6V-0014 | 液压油箱     | 1     | |
9U-6810 | 螺母     | 1     | |
124-4641 | 套筒     | 1     | |
124-4638 | 盘     | 1     | |
E     | 3S-6224     | 电动液压泵总成     | 1     |
9U-6814 | 拉拔器螺柱     | 1     | |
5P-5212 | 盘     | 1     | |
6V-0014 | 液压油箱     | 1     | |
9U-6810 | 螺母     | 1     | |
124-4641 | 套筒     | 1     | |
124-4639 | 盘     | 1     |
开始:
- 拆卸推臂和铲刀。 请参阅拆解和组装, "推臂和铲刀 - 拆卸"。
- 卸下驾驶室。 请参阅拆解和组装, "驾驶室 - 拆卸"。
- 卸下中心驱动轴。 请参阅拆解和组装, "驱动轴(中心) - 拆卸和安装"。
- 释放液压系统压力。 请参阅拆解和组装, "系统压力 - 释放"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
在工作温度下,液压油箱温度很高且处于压力下。 热油和热的部件可能会导致人身伤害。 不要让高温机油或部件与皮肤接触。 在安装或拆卸任何液压测试装置前,缓慢拧松注油口盖为液压油箱卸压。 |
注: 为便于安装,在所有管路、所有软管、所有导线及所有管上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和污染物进入系统。
- 将液压系统中的油排入合适的容器以便保存或废弃这些油。
- 断开线束组件 (3) 和软管组件 (1) 。 拆下卡箍 (2) 。
Show/hide table
图 1 | g01258133 |
- 从机具和制动器液压油箱断开软管组件 (4) 。
Show/hide table
图 2 | g00885102 |
Show/hide table
图 3 | g00885104 |
- 拆下卡箍 (5) ,断开软管组件 (6) 。
- 拆下护圈 (7) 。
Show/hide table
图 4 | g00885105 |
Show/hide table
图 5 | g00885107 |
- 使用工具 (A) 以便拆下销组件 (8) 。 对于其他转向油缸,重复本步骤。
- 如图所示,将工具 (B) 和适当的支座安置在后部机架下面。
Show/hide table
图 6 | g00885108 |
- 如图所示,将适当的起吊设备连接到前部机架上。 前部机架在起吊点处的重量约为 10000 kg (22000 lb)。
Show/hide table
图 7 | g00885109 |
- 如图所示,将适当的支座安置到前部机架下面。
- 如图所示,将适当的叉车固定至前部机架。
- 从下部铰接处底部拆卸螺栓 (9) 、螺栓 (10) 和板 (11) 。
Show/hide table
图 8 | g00885111 |
- 从销组件 (13) 卸下盖 (12) 。
Show/hide table
图 9 | g00885114 |
Show/hide table
图 10 | g00885115 |
- 使用工具 (C) 以便拆下销组件 (13) 。 销组件 (13) 的重量约为 43 kg (95 lb)。
- 从上部铰接处底部拆卸螺栓 (14) 、板 (15) 和垫片。
Show/hide table
图 11 | g00885116 |
- 断开软管组件 (16) 。
Show/hide table
图 12 | g00885117 |
- 拆卸螺栓 (18) 并重新将支架组件 (17) 放置在一边。
- 断开管组件 (19) 。
Show/hide table
图 13 | g00885118 |
- 拆卸螺栓 (21) 并将支架和空档器阀 (20) 移开。
Show/hide table
图 14 | g00885119 |
- 拆卸螺栓 (22) 、螺栓 (23) 和板 (24) 。
Show/hide table
图 15 | g00885120 |
- 卸下垫片 (25) 。
Show/hide table
图 16 | g00885121 |
- 使用工具 (C) 和适当的起吊设备,卸下销组件 (26) 。 工具 (C) 和销组件 (26) 的组合重量约为 159 kg (350 lb)。 不带工具 (C) 的销组件 (26) 的重量约为 70 kg (155 lb)。
Show/hide table
图 17 | g01258140 |
Show/hide table
图 18 | g01258142 |
- 分离转向机架锁连杆 (27) 。
Show/hide table
图 19 | g00885126 |
- 确保分离时位于上部铰接处底部的隔套远离发动机端机架。
Show/hide table
图 20 | g00880020 |
- 采用叉车将前部机架缓缓从后部机架拉开。
Show/hide table
图 21 | g00885128 |
- 继续移动前部机架,使前部机架与后部机架相距至少 610 mm (24 in)。
- 挡住前轮胎并重新安置适当的支座以支撑前机架。
- 从前部机架的上部铰接组件拆卸隔套 (28) 。
Show/hide table
图 22 | g00885129 |
- 标记上盖 (34) 和下盖 (32) 的径向位置。
Show/hide table
图 23 | g00885130 |
- 拆卸螺栓 (29) 、下盖 (32) 和上盖 (30) 。
- 卸下垫片 (31) 。
- 采用工具 (D) 以从上部铰接处拆卸两个轴承外圈和内圈。
Show/hide table
图 24 | g00885131 |
- 从下部铰接组件拆卸螺栓 (33) 和盖 (34) 。
Show/hide table
图 25 | g00885132 |
- 卸下垫片 (35) 。
- 从下部铰接组件拆卸螺栓 (36) 和下盖 (37) 。
Show/hide table
图 26 | g00885133 |
- 采用工具 (E) 以从下部铰接处拆卸两个轴承外圈和内圈。
Show/hide table
图 27 | g00885134 |
- 从上部铰接处和下部铰接处的所有四个盖上拆卸唇形密封。
Show/hide table
图 28 | g00885135 |
Caterpillar Information System:
2006/05/29 New Articulated Mirror Supports Being Used {7319}
C27 and C32 Engines for Caterpillar Built Machines Engine Fan Control Solenoid Circuit - Test
844H Wheel Dozer Machine Systems Selector and Pressure Control Valve (Secondary Steering) - Remove and Install
D7R Series 2 Track-Type Tractor Machine Systems Cab Mounting
C9.3 Tier 4 Final Engines Coolant Temperature Sensor
844H Wheel Dozer Machine Systems Pilot Operated Hydraulic Control (Joystick) - Install
854K Wheel Dozer Machine Systems Pilot Operated Hydraulic Control (Joystick) - Remove
2006/03/27 Correction to Specifications , "Main Control Valve" {5051}
993K Wheel Loader Engine Crankcase Breather - Clean
844H Wheel Dozer Machine Systems Main Control Valve - Install
844H Wheel Dozer Machine Systems Main Control Valve - Remove
844H Wheel Dozer Machine Systems Main Control Valve - Assemble
844H Wheel Dozer Machine Systems Front Frame to Rear Frame - Connect
Installation of the 288-6536 Control Valve Conversion Gp (Third Valve Kit){5051} Installation of the 288-6536 Control Valve Conversion Gp (Third Valve Kit){5051}
Installation of the 290-3538 Control Valve Conversion Gp (Third Valve Kit){5051, 5057, 5059, 5063} Installation of the 290-3538 Control Valve Conversion Gp (Third Valve Kit){5051, 5057, 5059, 5063}
C27 and C32 Engines for Caterpillar Built Machines Engine Fan Speed Sensor Circuit - Test
C13 Tier 4 Final Engines Fuel Pressure Sensor
C27 and C32 Engines for Caterpillar Built Machines Engine Oil Level Switch Circuit - Test
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Braking System Pump Performance (Pilot, Brake) - Test
D3K, D4K and D5K Track-Type Tractors Ripper Tip and Shank Protector
D3K, D4K and D5K Track-Type Tractors Lifting and Tying Down the Machine
D3K, D4K and D5K Track-Type Tractors Towing the Machine
631G and 637G Wheel Tractor-Scrapers Machine Systems Hydraulic Tank - Remove
C11 and C15 Engines for Caterpillar Built Machines E360 Low Engine Oil Pressure