Customer Parameters Worksheet
Record the following information before you change any parameter.
Show/hide table
| System Configuration Parameters | |
| Parameter | Present Value |
| Personality Module Interlock | |
| Electronic Control Module (ECM)
Serial Number |
|
| Engine Serial Number | |
| Equipment ID | |
| Full Load Setting (FLS) | |
| Full Torque Setting (FTS) | |
| "Fuel Ratio Control Offset (FRC)" | |
| "Rated Fuel Positon (mm)" | |
| Fuel Correction Factor (%) | |
| Low Idle (rpm) | |
| Droop (%) | |
| "Governor Gain Factor" | |
| "Governor Minumum Stability Factor" | |
| Acceleration Delay on start-up (sec) | |
| Acceleration Rate (rpm/sec) | |
| Programmable Torque Scaling | |
| "Engine Cooling System Configuration" | |
| Cold Cylinder Cutout | |
| "Cooldown Engine Speed (rpm)" | |
| "Engine Cooldown Duration (min)" | |
| "Engine Prelube Duration (sec)" | |
| "Crank Duration (sec)" | |
| "Maximum Number of Crank Cycles" | |
| "Crank Terminate Speed (rpm)" | |
| "Total Tattletale" | |
| Injector Code (1) | |
| Injector Code (2) | |
| Injector Code (3) | |
| Injector Code (4) | |
| Injector Code (5) | |
| Injector Code (6) | |
| Injector Code (7) | |
| Injector Code (8) | |
| Injector Code (9) | |
| Injector Code (10) | |
| Injector Code (11) | |
| Injector Code (12) | |
Record the following information from the engine monitoring system.
Show/hide table
| Engine Monitoring System | ||||||
| Warning Trip Point | Warning Delay Time | Derate Trip Point | Derate Delay Time | Shutdown Trip Point | Shutdown Delay Time | |
| Low System Voltage | ||||||
| Low Oil Pressure | ||||||
| High Coolant Temperature | ||||||
| Low Coolant Temperature | ||||||
| Engine Overspeed | ||||||
| Air Filter Restriction Pressure | ||||||
| Altitude | ||||||
| High Exhaust Temperature | ||||||
| Oil Filter Differential Pressure | ||||||
| Fuel Filter Differential Pressure | ||||||
| Crankcase Pressure | ||||||
| Aftercooler Water Temperature | ||||||
Caterpillar Information System:
3512C and 3516C Engines System Configuration Parameters
C7 Marine Engines Injection Actuation Pressure Sensor - Remove and Install
C7 Marine Engines Fuel Temperature Sensor - Remove and Install
C7 Marine Engines Boost Pressure Sensor - Remove and Install
C7 Marine Engines Coolant Temperature Sensor - Remove and Install
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Speed Sensor (Transmission)
3508C, 3512C and 3516C Marine Engines Camshaft - Install
2006/04/03 Improved Bracket for the Aftercooler Water Lines {1063}
3508C, 3512C and 3516C Marine Engines Camshaft - Remove
3508C, 3512C and 3516C Marine Engines Cylinder Liner - Install
C15 and C18 Generator Set Engines Fuel Transfer Pump - Install
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Output Transfer Yoke
C7 Marine Engines Speed/Timing Sensor - Remove and Install
Cleaning Fluid-Carrying Hose and Tube Assemblies In Shop and Field Applications {0645, 5050} Cleaning Fluid-Carrying Hose and Tube Assemblies In Shop and Field Applications {0645, 5050}
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Product Installation
C175 Generator Sets Before Starting Engine
C9 Marine Engines and C9 Marine Generator Sets Cylinder Head Valves
3508C, 3512C and 3516C Marine Engines Crankshaft - Remove
C15 and C18 Generator Set Engines Pump Drive - Disassemble
C15 and C18 Generator Set Engines Pump Drive - Assemble
C7 Marine Engines Engine Oil Pressure Sensor - Remove and Install
C7 Marine Engines Fuel Pressure Sensor - Remove and Install
C15 and C18 Generator Set Engines Engine Support (Front) - Remove and Install
C15 On-Highway Engine Variable Valve Actuator