3508C, 3512C and 3516C Marine Engines Caterpillar


Cylinder Liner - Install

Usage:

3512C 2A2

安装步骤

表 1
所需工具 
工具  零件号  零件描述  数量 
2P-8260  缸套安装器 
Loctite 硅润滑剂 / 绝缘润滑脂
LB 8801/LB 8423(1) 
— 
- LB-8104 1652339(2)  — 
砂布 (精细) 
(1) 首选润滑脂
(2) 仅用于 EAME


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损並縮短部件使用寿命。


  1. 检查缸套突出量。 请参阅测试和调整, "缸套突出量"。


    图 1g03326886

  2. 缸套准备就绪后,利用工具 (B) 将缸套压入缸体中。

  3. 使用 0.02 mm (0.001 inch) 塞尺确认缸套紧贴缸体。 在多个位置检查是否存在间隙。 如果缸套和缸体之间存在间隙,则说明缸套密封圈受到夹持。 受到夹持的缸套密封圈会降低缸套密封圈和缸盖垫圈的使用寿命。

缸套密封的类型

缸套上可采用两种密封。

1 型



    图 2g02130336


    图 3g02248239

  1. 将肥皂液涂抹到 O 形密封圈 (1) 的环槽和 O 形密封圈 (1) 上。 将 O 形密封圈 (1) 安装到缸套 (2) 上。 另外,用肥皂液涂底部缸体孔的位置 (N)。

  2. 将加注口带箍 (3) 浸泡在清洁的发动机机油中。 将加注口带箍 (3) 立即安装到缸套 (2) 上。

  3. 在加注口带箍 (3) 可以膨胀前,立即安装缸套 (2)。

2 型



    图 4g02175641

  1. 为了安装缸套密封圈,缸套密封圈 (4) 在缸套孔的顶部边缘需要一个加工导角。

  2. 倒角可以加工在缸体内缸套孔的顶边上。 关于加工倒角的正确程序,请参阅专门说明书, SEBF9203。

    注: 也可以采用带有倒角的缸套座镶圈。 请参阅再使用和修补指南, SEBF8255。

  3. 将工具 (D) 用于顶部缸体孔内表面的位置 (M)。

  4. 确保缸套密封圈 (4) 的缸套槽清洁、干燥。 将缸套密封圈 (4) 安装在缸套 (2) 上。 将薄薄的一层工具 (C) 涂覆到加工倒角上的缸体上,涂抹宽度延伸到加工倒角下方 5 mm (0.2 inch) 的距离。 将工具 (C) 涂覆到缸套密封圈 (4) 上。

    注: 不要将工具 (C) 涂覆到缸套法兰或缸体顶部。

  5. 将肥皂液涂抹到 O 形密封圈 (1) 的环槽和 O 形密封圈 (1) 上。 将 O 形密封圈 (1) 安装到缸套 (2) 上。 另外,用肥皂液涂底部缸体孔的位置 (N)。

结束:

  1. 安装活塞和连杆组件。

Caterpillar Information System:

C15 and C18 Generator Set Engines Fuel Transfer Pump - Install
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Output Transfer Yoke
C9 Marine Engines and C9 Marine Generator Sets Cylinder Head Valves
2006/03/20 A New Replacement Kit for the Bezel is Now Used on the Integrated Control Head {1915}
C15 and C18 Generator Set Engines Fuel Transfer Pump - Remove
C175 Generator Sets Engine Stopping
C15 and C18 Generator Set Engines Pump Drive - Install
C15 and C18 Generator Set Engines Pump Drive - Remove
C3.3 Industrial Engine Exhaust Elbow - Remove and Install - If Equipped
C15 and C18 Generator Set Engines Fan Drive - Install
C3.3 Industrial Engine Air Inlet and Exhaust System - Inspect
3508C, 3512C and 3516C Marine Engines Engine Oil Sequence Valves - Remove and Install
3508C, 3512C and 3516C Marine Engines Camshaft - Remove
2006/04/03 Improved Bracket for the Aftercooler Water Lines {1063}
3508C, 3512C and 3516C Marine Engines Camshaft - Install
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Speed Sensor (Transmission)
C7 Marine Engines Coolant Temperature Sensor - Remove and Install
C7 Marine Engines Boost Pressure Sensor - Remove and Install
C7 Marine Engines Fuel Temperature Sensor - Remove and Install
C7 Marine Engines Injection Actuation Pressure Sensor - Remove and Install
3512C and 3516C Engines System Configuration Parameters
3512C and 3516C Engines Customer Parameters Worksheet
C7 Marine Engines Speed/Timing Sensor - Remove and Install
Cleaning Fluid-Carrying Hose and Tube Assemblies In Shop and Field Applications {0645, 5050} Cleaning Fluid-Carrying Hose and Tube Assemblies In Shop and Field Applications {0645, 5050}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.