Engine Oil Pump - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
- 安装 O 形密封圈 (34) 。 安装 O 形密封圈 (33) 。 安装管 (32) 。 安装螺栓 (29) 。 安装壳体 (30) 。 安装螺栓 (29) 。
Show/hide table
图 1 | g01287417 |
Show/hide table
图 2 | g01287407 |
- 将调节阀的杆 (25) 、垫片 (26) 、挡圈 (27) 和弹簧 (28) 安装到调节器组件 (11) 中。 将最大压力安全阀的杆 (21) 、垫片 (22) 、挡圈 (23) 和弹簧 (24) 安装到调节器组件 (11) 中。
Show/hide table
图 3 | g01287406 |
- 安装 O 形密封圈 (20) 。
Show/hide table
图 4 | g01558136 |
- 将盖 (19) 安装到调节器组件 (11) 上。 安装垫圈和螺栓 (18) 。
Show/hide table
图 5 | g01558135 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将工具 (A) 和适当的起吊设备连接到发动机油泵 (17) 上。 发动机机油泵 (17) 的重量约为 50 kg (110 lb)。 将发动机机油泵 (17) 安置到发动机上。 安装螺栓 (16) 。
Show/hide table
图 6 | g01242498 |
- 安装法兰组件和弯头 (15) 。 安装螺栓 (13) 和 (14) 。
Show/hide table
图 7 | g01242497 |
- 将适当的起吊设备连在歧管 (11) 上。 歧管 (11) 的重量约为 34 kg (75 lb)。 将歧管 (11) 安置在发动机机油泵上。 安装螺栓 (12) 。
Show/hide table
图 8 | g01242431 |
- 连接管组件 (10) 。 安装螺栓 (9) 。 连接管组件 (8) 。 安装螺栓 (7) 。 安装软管组件 (6) 。
Show/hide table
图 9 | g01242430 |
- 安装密封垫和进气歧管 (4) 的末尾段。 安装螺栓 (3) 。 安装螺栓 (5) 。
Show/hide table
图 10 | g01242429 |
- 将线束组件的盖 (1) 安置到进气歧管上。 安装螺栓 (2) 。
Show/hide table
图 11 | g01242428 |
Caterpillar Information System:
C15 and C18 Generator Set Engines CID 0091 FMI 08 Throttle Position signal abnormal
C3.3 and C4.4 Rental Generator Sets Additional Messages
Hose and Coupling Assembly and Repair Process Guide{0684, 3016, 3103, 3154, 4133, 4257, 4304, 5057, 7554} Hose and Coupling Assembly and Repair Process Guide{0684, 3016, 3103, 3154, 4133, 4257, 4304, 5057, 7554}
CX31 and CX31 HT On-Highway Transmissions General Troubleshooting Information
C15 and C18 Generator Set Engines Alternator - Remove and Install
C175 Generator Set Engines Engine Oil Pump - Remove
C15 and C18 Generator Set Engines Electronic Control Module - Remove and Install
3512C and 3516C Engines Starting Motor System
3512C and 3516C Engines Speed Control
2006/04/17 Slide Sledge Heavy Equipment Repair Tools Are Now Available {0599, 0644}
C7 Marine Engines Oil Cooler (Transmission, Auxiliary) - Remove and Install
3512C and 3516C Engines Pulse Width Modulated Sensor
C15 and C18 Generator Set Engines Electric Starting Motor - Remove and Install
3512C and 3516C Engines Sensor Supply
C175 Generator Set Engines Air Inlet Manifold - Remove and Install
3176C and 3196 Engines for Caterpillar Built Machines Belt Tensioner
3512C and 3516C Engines Analog Sensor (Passive)
C175-16 and C175-20 Engines for Caterpillar Built Machines Fuel Pump (High Pressure) - Remove and Install
C15 and C18 Generator Set Engines Fan Drive - Remove
3508C, 3512C and 3516C Marine Engines Engine Oil Sequence Valves - Remove and Install
C3.3 Industrial Engine Air Inlet and Exhaust System - Inspect
C15 and C18 Generator Set Engines Fan Drive - Install
C3.3 Industrial Engine Exhaust Elbow - Remove and Install - If Equipped
C15 and C18 Generator Set Engines Pump Drive - Remove