Electronic Control Module - Remove and Install
拆卸步骤
- 断开蓄电池处的蓄电池负极接线端。 请参阅操作和保养手册蓄电池或蓄电池电缆, "- 断开"。
- 松开六角头固定螺钉 (3) 。 断开电子控制模块 (1) 上的线束组件。
Show/hide table
图 1 | g01100462 |
- 拆下螺栓 (4) 。 拆下电子控制模块 (1) 和接地电缆带 (2) 。
- 从电子控制模块 (1) 上拆下垫圈和隔离块。
安装步骤
- 把隔离块固定在电子控制模块 (1) 上。 将隔套、接地电缆带 (2) 和电子控制模块 (1) 安置在支架组件上,并安装螺栓 (4) 。
Show/hide table
图 2 | g01100462 |
- 连接线束组件和电子控制模块 (1) 。 拧紧六角头螺钉 (3) 至扭矩为 6 ± 1 N·m (53 ± 9 lb in)。
- 连接蓄电池处的蓄电池负极接线端。 请参阅操作和保养手册蓄电池或蓄电池电缆, "- 断开"。
Caterpillar Information System:
3512C and 3516C Engines Starting Motor System
3512C and 3516C Engines Speed Control
2006/04/17 Slide Sledge Heavy Equipment Repair Tools Are Now Available {0599, 0644}
C7 Marine Engines Oil Cooler (Transmission, Auxiliary) - Remove and Install
3512C and 3516C Engines Pulse Width Modulated Sensor
3500 Engines Balancer Group (Front) - Remove and Install - 3508C Engine
D Series Excavator Monitoring System Performance Mode
3406E, C-10, C-12, C-15, C-16 Truck Engines Reference Material
C13, C15, and C18 Generator Set Engines CID 1690 FMI 08 Throttle #2 Position Sensor abnormal frequency, pulse width, or period
3500 Engines Housing (Front) - Install
C7 Marine Engines Unit Injector Hydraulic Pump - Install
C15 and C18 Petrolem Generator Set Engines Diagnostic Code Cross Reference
C175 Generator Set Engines Engine Oil Pump - Remove
C15 and C18 Generator Set Engines Alternator - Remove and Install
CX31 and CX31 HT On-Highway Transmissions General Troubleshooting Information
Hose and Coupling Assembly and Repair Process Guide{0684, 3016, 3103, 3154, 4133, 4257, 4304, 5057, 7554} Hose and Coupling Assembly and Repair Process Guide{0684, 3016, 3103, 3154, 4133, 4257, 4304, 5057, 7554}
C3.3 and C4.4 Rental Generator Sets Additional Messages
C15 and C18 Generator Set Engines CID 0091 FMI 08 Throttle Position signal abnormal
C175 Generator Set Engines Engine Oil Pump - Install
C15 and C18 Generator Set Engines Electric Starting Motor - Remove and Install
3512C and 3516C Engines Sensor Supply
C175 Generator Set Engines Air Inlet Manifold - Remove and Install
3176C and 3196 Engines for Caterpillar Built Machines Belt Tensioner
3512C and 3516C Engines Analog Sensor (Passive)