Torque Converter (Lockup) - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7573     | 连杆支架     | 4     |
B     | 1U-9200     | 杠杆式提升起重机     | 1     |
C     | 138-7575     | 连杆支架     | 3     |
开始:
- 拆卸转向泵。 请参阅拆解和组装, "活塞泵(转向)- 拆卸"。
- 拆卸机具液压泵。 请参阅拆解和组装, "活塞液压泵(串联、机具)- 拆卸"。
- 卸下输入驱动轴。 对于正在维修的机器,请参阅拆解和组装, "输入驱动轴 - 拆卸和安装"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
高温机油或高温部件可能会导致人身伤害。 在工作温度下,机油温度高,压力高。 热油能造成烫伤。 只能在发动机停机且加注口盖充分冷却到可以徒手触及时再卸下加注口盖。 不让高温油或部件与皮肤接触。 |
注: 为便于安装,在所有管路、所有软管、所有导线及所有管上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和污染物进入系统。
- 关闭加热器软管阀。
- 断开线束组件 (1) 。 拆下螺栓 (2) 。 需要两个人拆卸扶手组件 (3) 。 对另一侧重复此操作。
Show/hide table
图 1 | g01252702 |
- 断开线束组件 (4) 和所有的安装紧固件。 断开软管组件 (5) 。
Show/hide table
图 2 | g01252739 |
- 断开软管组件 (6) 。
Show/hide table
图 3 | g01252754 |
- 拆下螺栓 (7) 。 将工具 (C) 和适当的起吊设备连接到盖组件 (8) 上。 盖组件 (8) 的重量约为 159 kg (350 lb)。 拆下盖组件 (8) 。
Show/hide table
图 4 | g01253114 |
- 断开软管组件 (9) 。
Show/hide table
图 5 | g01253162 |
- 拆下螺栓 (10) 。 将工具 (C) 和适当的起吊设备连接到盖组件 (11) 上。 盖组件 (11) 的重量约为 118 kg (260 lb)。 拆下盖组件 (11) 。
Show/hide table
图 6 | g01253170 |
- 拆下夹子 (12) 。
Show/hide table
图 7 | g01239011 |
- 拆卸螺栓 (13) 并移开液压油滤清器底座 (14) 。
- 断开软管组件 (15) 。
Show/hide table
图 8 | g01239015 |
Show/hide table
图 9 | g01253231 |
- 断开软管组件 (16) 。
- 拆卸螺栓 (17) 并移开液压油滤清器底座 (18) 。
- 拆下支架 (19) 。
- 拆下夹子 (20) 。
Show/hide table
图 10 | g01239016 |
- 卸下支架 (21) 。 拆下夹子 (22) 。
Show/hide table
图 11 | g01239018 |
- 拆下螺栓 (23) 。
- 卸下支架 (24) 。 卸下支架 (25) 。
Show/hide table
图 12 | g01239611 |
- 拆卸螺栓 (26) 并移开液压油滤清器底座 (27) 。
- 拆卸螺栓 (28) 并移开液压油滤清器底座 (29) 。
Show/hide table
图 13 | g01240058 |
Show/hide table
图 14 | g01253247 |
- 将工具 (A) 和适当的起吊设备连接至面板组件 (30) 。 面板组件 (30) 的重量约为 82 kg (180 lb)。
注: 将离驾驶室最近的链条长度调整约 305 mm (12.0 in)。
Show/hide table
图 15 | g01240076 |
- 拆下螺栓 (31) ,然后拆下面板组件 (30) 。
Show/hide table
图 16 | g01240082 |
Show/hide table
图 17 | g01240083 |
Show/hide table
图 18 | g01240090 |
- 断开软管组件 (32) 、软管组件 (33) 、软管组件 (34) 、软管组件 (35) 和软管组件 (36) 。
Show/hide table
图 19 | g01240094 |
- 断开软管组件 (37) 。
Show/hide table
图 20 | g01240099 |
- 拆下夹子 (38) 。 断开线束组件 (39) 。
Show/hide table
图 21 | g01240104 |
- 拆下螺栓 (40) ,以断开适配器体 (41) 和软管组件 (42) 。
- 将工具 (A) 、工具 (B) 和适当的起吊设备连接到变矩器 (43) 上。 变矩器 (43) 的重量约为 476 kg (1050 lb)。
Show/hide table
图 22 | g01240256 |
Show/hide table
图 23 | g01240113 |
- 拆下夹子 (44) 。 卸下支架 (45) 。
- 拆下螺栓 (46) 然后拆下变矩器 (43) 。
Caterpillar Information System:
Payload Control System (PCS) 2.X System Schematic
Payload Control System (PCS) 2.X Glossary of Electrical Terms
Payload Control System (PCS) 2.X Battery (Internal Backup) - Replace
Payload Control System (PCS) 2.X Position Sensor (Lift Linkage) - Adjust
Payload Control System (PCS) 2.X Payload Electronic Control Module - Replace
Payload Control System (PCS) 2.X MID 074 - CID 0820 - FMI 02
Payload Control System (PCS) 2.X MID 074 - CID 0817 - FMI 12
Payload Control System (PCS) 2.X MID 074 - CID 0817 - FMI 08
Payload Control System (PCS) 2.X MID 074 - CID 0817 - FMI 04
Payload Control System (PCS) 2.X MID 074 - CID 0769 - FMI 08
Payload Control System (PCS) 2.X MID 074 - CID 0769 - FMI 02
Payload Control System (PCS) 2.X MID 074 - CID 0769 - FMI 01
844H Wheel Dozer and 990H Wheel Loader Power Train Torque Converter (Lockup) - Install
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders Engine Shutdown Switch Circuit - Test
2006/03/20 Three Seal Installers Available for Servicing Hand Metering Units {0732, 4312}
993K Wheel Loader Engine Oil and Filter - Change
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders Throttle Position Sensor Circuit - Test
990H Wheel Loader Machine Systems Pilot Operated Hydraulic Control - Install
525C, 535C and 545C Wheel Skidders Machine Monitor System Component Description
2006/02/13 Barrel Adapter Allows Technician to Attach Filter Unit to Barrel {0645, 0680}
525C, 535C and 545C Wheel Skidders Machine Monitor System Features
D3K, D4K and D5K Track-Type Tractors Electrohydraulic System Angle Cylinder (Bulldozer)
Custom Product Support Literature for the 980H Wheel Loaders that have a Steel Mill Arrangement{7000} Custom Product Support Literature for the 980H Wheel Loaders that have a Steel Mill Arrangement{7000}
990H Wheel Loader Machine Systems Expansion Tank (Air) (European Market) - Remove