Vane Pump (Implement, Steering, Pilot and Braking) - Install
Installation Procedure
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
- Install O-ring seal (13) (not shown).
Show/hide table
Illustration 1 | g01205632 |
- Install check valve (14) .
- Install the O-ring seal to elbow (15) .
- Install elbow (15) and the four bolts.
- Install the O-ring seal to elbow (16) .
- Install elbow (16) and the four bolts.
- Attach a suitable lifting device to vane pump (11). The weight of vane pump (11) is approximately 59 kg (130 lb).
Show/hide table
Illustration 2 | g01205279 |
- Install vane pump (11) .
- Install two bolts (12) .
- Install the O-ring seal to tube assembly (10) .
Show/hide table
Illustration 3 | g01205266 |
- Install tube assembly (10) and the four bolts.
- Install hose assemblies (8) and (9) .
- Connect fitting (7) to pilot oil pump check valve.
Show/hide table
Illustration 4 | g01205284 |
- Install bolt (5) to bracket (6) .
Show/hide table
Illustration 5 | g01205282 |
- Install cover (4) .
Show/hide table
Illustration 6 | g01205281 |
- Install bracket (3) and the two bolts.
- Install crossbeam (2) and the four bolts.
Show/hide table
Illustration 7 | g01205275 |
- Install cover (1) .
- Fill the hydraulic tank. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the hydraulic tank. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the proper filling procedure.
End By:
- Install the hood. Refer to Disassembly and Assembly, "Hood - Remove and Install".
- Remove the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Caterpillar Information System:
R1300G Series II Load Haul Dump Machine Systems Vane Pump (Implement, Steering, Pilot and Braking) - Disassemble
R1600G Load Haul Dump Power Train Final Drive Planetary Carrier - Assemble
R1600G Load Haul Dump Power Train Final Drive Planetary Carrier - Disassemble
R1300G Series II Load Haul Dump Power Train Output Drive
R1300G Series II Load Haul Dump Power Train Transmission Hydraulic Control
R1300G Series II Load Haul Dump Power Train Temperature Sensor (Transmission Oil)
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
777F Off-Highway Truck Rear Axle A-Frame Bearing - Lubricate
793D Off-Highway Truck Air System and Brakes Parking and Secondary Brake Release System Leakage - Check
3516B Off-Highway Trucks Pulse Width Modulated Sensor
D7R Series 2 Track-Type Tractor Power Train Transmission Mounting
740 Articulated Truck, 768C, 769C, 769D, 772B, 773B, 773D, 773E, 773F, 776, 776B, 776C, 776D, 777, 777B, 777C, 777D, 777F, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C and 793D Off-Highway Trucks and 771C, 771D, 775B, 775 Pressure Switch (Air)
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Scavenge Pump - Remove
D7R Series 2 Track-Type Tractor Power Train Bevel and Transfer Gears
CB-534D, CB-534D Series XW and CB-564D Vibratory Compactors Engine Supplement Fuel Priming Pump and Fuel Filter Base - Remove and Install
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System Electronic Control Module (ECM) - Configure
M325D MH Material Handler Air Conditioning and Heating Control
793D Off-Highway Truck Air System and Brakes Relief Valve (Brake Oil Cooler) - Test and Adjust
2005/09/26 A New Fuel Lift Pump is Now Available {1256, 1258}
AP-1000D and BG-260D Asphalt Pavers Machine Systems Electric Motor (Screed Burner Fuel Pump) - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Scavenge Pump - Install
966H Wheel Loader and 972H Wheel Loader Power Train MID 081 - CID 1400 - FMI 06
C15 and C18 Engines for Caterpillar Built Machines Alternator Mounting
416E Backhoe Loader Extendable Stick Pads - Inspect/Adjust - If Equipped