Water Temperature Regulator - Remove and Install
- Drain the coolant from the cooling system into a suitable container for storage or disposal until the coolant is below the level of the water temperature regulator housing. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Show/hide table
Illustration 1 g01222528 - Remove elbows (5).
- Remove bolts (4), the washers, and spacers (3).
- Remove bolts (2) from water temperature regulator housing (1).
Show/hide table
Illustration 2 g01222549 - Remove water temperature regulator housing (1). Remove O-ring seals (7) from water temperature regulator housing (1). Remove water temperature regulators (6) from water temperature regulator housing (1).
- If necessary, remove the lip seals from water temperature regulator housing (1).
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 221-8647 | Seal Installer Gp | 1 |
- If necessary, use Tooling (A) to install the lip seals in water temperature regulator housing (1).
Show/hide table
Illustration 3 g01222549 - Install water temperature regulators (6) in water temperature regulator housing (1).
- Install new O-ring seals (7) in water temperature regulator housing (1).
Show/hide table
Illustration 4 g01222528 - Position water temperature regulator housing (1).
- Install spacers (3), the washers, and bolts (4).
- Install bolts (2).
- Install elbows (5).
- Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Caterpillar Information System:
2005/11/28 The 6V-8633 Connector Has Changed {5057, 7553}
C32 Petroleum Engines Water Pump - Install
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Travel Motor - Disassemble
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Bucket - Install
C15 Generator Set Engines Can Not Reach Top Engine RPM
3600 Distillate Fuel Engines Turbocharger - Inspect - Napier Turbocharger - If Equipped
C32 Petroleum Engines Water Pump - Remove
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Track Roller - Install
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Track Roller - Remove
3412 Generator Set Engines Valve Rocker Arms, Lifters, and Bridges
C175-16 and C175-20 Engines for Caterpillar Built Machines Cylinder Head - Remove
3412 Generator Set Engines Valve Rocker Arms, Lifters, and Bridges
C6.6 Generator Set Injector Data Incorrect - Test
C15-XQ400 Rental Generator Set Additional Messages
C27 and C32 Generator Set Engines Excessive Black Smoke
C11 and C13 Engines Exhaust Manifold
C27 and C32 Generator Set Engines CID 1785 FMI 03 Intake Manifold Pressure Sensor voltage high
C27 and C32 Generator Set Engines CID 1785 FMI 04 Intake Manifold Pressure Sensor voltage low
G3500 A3 Engines System Overview
C175 Generator Set Engines Crankcase Breather - Remove and Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Rocker Shaft and Push Rods - Remove
3412 Generator Set Engines Valve Mechanism Cover
C32 Petroleum Engines Flywheel - Remove
C175-16 and C175-20 Engines for Caterpillar Built Machines Rocker Shaft and Push Rods - Install