Swivel - Disassemble
拆解步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 6V-3822 | 螺栓 | 2 |
| 6 V-5839 | 垫圈 | 2 | |
| 1P-5546 | 十字挡块 | 1 | |
| 5P-4168 | 踏脚板 | 1 | |
| 5F-7366 | 螺钉 | 1 | |
| B | 1P-2420 | 变速箱修复台 | 1 |
开始:
- 拆下旋转接头。 请参阅拆解和组装, "回转接头 - 拆卸"。
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品，参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 拆解之前，请彻底清洁旋转接头的外表面。
- 如图所示，将旋转接头紧固到工具 (B) 。 旋转接头的重量约为 43 kg (95 lb)。
Show/hide table
 | |
| 图 1 | g00633843 |
Show/hide table
 | |
| 图 2 | g00633841 |
- 从外部壳体 (8) 上拆下螺栓 (1) 、垫圈 (2) 和盖 (3) 。
- 从外部壳体 (8) 拆下 O 形密封圈 (7) 。
- 从转子 (11) 上拆下螺栓 (4) 、垫圈 (5) 和挡圈 (6) 。
- 使用工具 (A) 以便将外部壳体 (8) 从转子 (11) 分离。 外部壳体 (8) 的重量约为 20 kg (45 lb)。 转子 (11) 的重量约为 21 kg (46 lb)。
- 从外部壳体 (8) 拆下密封件 (9) 。
- 从外部壳体 (8) 拆下 O 形密封圈 (10) 。
- 拆下螺塞 (13) 。 从螺塞 (13) 拆下 O 形密封圈 (12) 。
Caterpillar Information System:
Using Lock-N-Stitch Procedures for Casting Repair {0676, 0685} Using Lock-N-Stitch Procedures for Casting Repair {0676, 0685}
3412 Generator Set Engines Fuel Injection Pump
C15 Generator Set Engines 5 Volt Engine Pressure Sensor Supply Circuit - Test
C1.5 and C2.2 Generator Set Engines Pistons and Connecting Rods - Install
3412 Generator Set Engines Fuel Injection Pump Housing
C15 Generator Set Engines CAN Data Link Circuit - Test
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Track Adjuster - Assemble
Start-up Procedure after a System Generated Shutdown{1000} Start-up Procedure after a System Generated Shutdown{1000}
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Upper Frame and Undercarriage Frame - Connect
Hydraulic Cylinder Seal Failure Analysis {7555, 7562} Hydraulic Cylinder Seal Failure Analysis {7555, 7562}
C1.5 and C2.2 Generator Set Engines Pistons and Connecting Rods - Remove
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Track Adjuster - Disassemble
3412 Generator Set Engines Fuel Transfer Pump
3412 Generator Set Engines Fuel Transfer Pump
C15 Generator Set Engines Ether Injection System - Test
C15 Generator Set Engines E255 Diagnostic Reset
C1.5 and C2.2 Generator Set Engines Connecting Rod Bearings - Remove
C1.5 and C2.2 Generator Set Engines Connecting Rod Bearings - Install
345C MHPU Mobile Hydraulic Power Unit Machine Systems Swivel - Assemble
C4.4 and C6.6 Engines for Caterpillar Built Machines ECM Harness Connector Terminals
C15 and C18 Engines for Caterpillar Built Machines Water Temperature Regulator Housing
345C MHPU Mobile Hydraulic Power Unit Machine Systems Swing Drive - Disassemble
C1.5 and C2.2 Generator Set Engines Coolant Temperature Switch - Remove and Install
C1.5 and C2.2 Generator Set Engines Engine Oil Pressure Switch - Remove and Install