C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Caterpillar


CID 0091 FMI 04

Usage:

C4.4 444
Conditions Which Generate This Code:

The Electronic Control Module (ECM) detects all of the following conditions:

  • The ECM has been powered for at least 3 seconds.

  • A signal voltage for the throttle position is below the diagnostic lower limit that is set for the application.

  • The power supply for the throttle sensor is within the expected range.

System Response:

If equipped, the warning light will come on. The ECM logs the diagnostic code if the engine is running.

If a second throttle is installed, the engine will use the second throttle until the fault is repaired.

If a second throttle is not installed or if the second throttle has a fault, the following conditions will occur:

  • The engine will default to the limp home speed.

  • If the engine speed is higher than the limp home speed, the engine will decelerate to the limp home speed.

  • If the engine speed is lower than the limp home speed, the engine speed will remain at the current speed.

  • The engine will remain at this speed while the diagnostic code remains active.

  • All inputs from the faulty throttle are ignored by the ECM until the fault is repaired.

  • All inputs from the repaired throttle will be ignored by the ECM until the keyswitch has been turned to the OFF position and then back to the ON position.

Monitor the configuration screen on the electronic service tool in order to determine the type of throttle position sensor that is used on the engine.

If the engine is equipped with an analog throttle position sensor, proceed to "Test Step 1".

If the engine is equipped with a digital throttle position sensor, proceed to "Test Step 2".

Test Step 1. Perform the following diagnostic procedure: Analog Throttle Position Sensor Circuit - Test

Results:

  • OK - STOP

Test Step 2. Perform the following diagnostic procedure: Digital Throttle Position Sensor Circuit - Test

Results:

  • OK - STOP

Caterpillar Information System:

C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0091 FMI 03
C6.6 Engines for Caterpillar Built Machines Engine Oil Pressure
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0091 FMI 02
C6.6 Industrial Engine Basic Engine
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Alternator - Remove and Install
C9-XQ300 Rental Generator Set Control Panel
C32 Marine and Auxiliary Marine Engines Vibration Damper and Pulley - Remove and Install
3500 Engines with EUI Option Crankshaft Position for Fuel Injector Adjustment and Valve Lash Setting
C9-XQ300 Rental Generator Set XQ Rental Generator Set Support
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Control Module (Automatic Temperature Control Unit) - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Pressure Switch (Refrigerant Pressure Cutoff) - Remove and Install
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 2246 FMI 06
C4.4 and C6.6 Engines for Caterpillar Built Machines CID 0247 FMI 09
C32 Marine Engines Crankshaft Front Seal - Install
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 02
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0707 - FMI 03
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Electric Starting Motor - Remove and Install
C9-XQ300 Rental Generator Set Before Towing
C9-XQ300 Rental Generator Set Fuel Related Components in Cold Weather
C15 Generator Sets Cold Weather Starting
C-12 Generator Set Engine CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C32 Marine and Auxiliary Marine Engines Housing (Front) - Remove
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 03
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 04
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.