Travel on Level Ground - Test
Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the engine speed that was used for this test.
Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".
Show/hide table
Required Tools     | |
---|---|
Description     | Qty     |
Tape Measure     | 1     |
Stopwatch     | 1     |
- Travel distance must be at least 30 m (98.4 ft) long. Travel test ground must be hard and as level as possible.
Show/hide table
Illustration 1 | g00816299 |
(A) Preliminary run 10 m (32.8 ft) (B) Travel distance 20 m (65.6 ft) |
- Draw a 30 m (98.4 ft) straight line on travel test ground as a reference line.
- Start the engine.
- Place the engine speed dial in the HIGH IDLE position.
- Increase the hydraulic oil temperature to 55° ± 5°C (131° ± 9°F).
- The bucket should be empty.
- Position the machine so that one track is parallel with the reference line. Position the machine for the travel test. Refer to Illustration 1.
- Place the travel speed control switch on the HIGH position.
- Move the machine by operating both travel levers at the same time.
- The first 10 m (32.8 ft) are for a preliminary run. Measure the travel time that is required to travel the remaining 20 m (65.6 ft). Measure the time that is required in each direction.
- Measure the travel deviation from the reference line.
- Place the travel speed control switch on the LOW position and repeat Steps 9 through 11.
Show/hide table
Travel Time     | ||
---|---|---|
Travel Speed     | Specification     | |
HIGH     | Forward     | 17.5 ± 2.5 sec     |
Reverse | ||
LOW     | Forward     | 26.0 ± 1.5 sec     |
Reverse |
Note: The following table represents the travel deviation (distance) from the reference line.
Show/hide table
Travel Deviation     | ||
---|---|---|
Travel Speed     | Specification     | |
HIGH     | Forward     | 1500 mm (59 inch) or less     |
Reverse | ||
LOW     | Forward     | 1500 mm (59 inch) or less     |
Reverse |
Caterpillar Information System:
302.5C Mini Hydraulic Excavator Hydraulic System Engine Performance - Test - Engine Speed
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System General Testing and Adjusting Information
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System Hydraulic System Pressure - Release
302.5C Mini Hydraulic Excavator Hydraulic System Swing Speed and Swing Drift on a Slope - Check
302.5C Mini Hydraulic Excavator Hydraulic System Machine Drift on a Slope - Check
302.5C Mini Hydraulic Excavator Hydraulic System Main Hydraulic Pump Air - Purge
302.5C Mini Hydraulic Excavator Hydraulic System Operational Checks
302.5C Mini Hydraulic Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
302.5C Mini Hydraulic Excavator Hydraulic System Relief Valve (Line) - Test and Adjust
302.5C Mini Hydraulic Excavator Hydraulic System Specifications
302.5C Mini Hydraulic Excavator Hydraulic System Relief Valve (Main) - Test and Adjust
302.5C Mini Hydraulic Excavator Hydraulic System Relief Valve (Swing) - Test and Adjust
302.5C Mini Hydraulic Excavator Hydraulic System Cylinder Speed - Check
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Machine System Visual Inspection
302.5C Mini Hydraulic Excavator Hydraulic System Cylinder Drift - Check
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System Accumulator (Pilot) - Test and Charge
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Engine - Install
C18 Generator Sets Cooling System Supplemental Coolant Additive (SCA) - Test/Add
390D Excavator Machine Systems Actuator Motor (Air Distributor) - Remove and Install
390D Excavator Machine Systems Blower Motor (Air Conditioner, Heater) - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Heater Core - Remove
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Heater Core - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Evaporator Coil - Remove
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Evaporator Coil - Install