Transmission Hydraulic Control - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
A     | 138-7573     | 连杆支架     | 2     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零件。 棉绒可能会留在零部件上,从而可能导致出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新件进行更换。 脏污及其它污物可能会损坏精密部件。 应在清洁的工作面上执行组装步骤。 总是盖好并保护好部件。
注: 检查 O 形密封圈、密封垫和密封是否磨损或损坏。 必要时,更换部件。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 将工具 (A) 和适当的起吊设备连接在变速箱液压控制阀 (15) 上。 变速箱液压控制阀 (15) 的重量约为 70 kg (155 lb)。 安置变速箱液压控制阀 (15) 。 安装螺栓 (14) 。
Show/hide table
图 1 | g01187006 |
- 安装管 (13) 。 定置盘组件 (12) ,安装螺栓 (11) 。
Show/hide table
图 2 | g01187090 |
- 安装法兰 (7) ,连接线束组件 (8) 。 连接软管组件 (6) 。
Show/hide table
图 3 | g01186757 |
Show/hide table
图 4 | g01186762 |
- 安装管 (9) 。 安装阀组件 (4) 和螺栓 (5) 。
注: 联轴节组件 (10) 上槽口的方位必须保持正确。
- 安装盘组件 (3) 。 安装盘 (1) 。 连接线束组件 (2) 。
Show/hide table
图 5 | g01186744 |
Caterpillar Information System:
TH48-E80 Oil/Gas Transmission Transmission Hydraulic Control - Remove
3126B Generator Set Engine CID 0164 FMI 02 Injector Actuation Pressure signal erratic
C13 and C15 On-highway Engines ECM Memory - Test
C7 and C9 Marine Engines Engine Cranks but Will Not Start
G3500 Engines Model View Illustrations
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0700 - FMI 02
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0590 - FMI 12
C7 and C9 On-Highway Engines Engine Rating Parameters
2005/07/01 A Improved Gasket is Now Available {1151, 1162}
Supplemental Parts and Service Information for the C18 Marine Propulsion Engine {1901, 7470} Supplemental Parts and Service Information for the C18 Marine Propulsion Engine {1901, 7470}
2005/07/18 A Improved Gasket is Now Available {1151, 1162}
3126B Petroleum Engine Air Shutoff - Install
Guidelines for Installation and Maintenance of Sea Water Heat Exchangers, Strainers, and Fuel Coolers{1379, 3319} Guidelines for Installation and Maintenance of Sea Water Heat Exchangers, Strainers, and Fuel Coolers{1379, 3319}
C32 Petroleum Engines Water Temperature Regulator - Remove and Install
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0702 - FMI 02
C18 Generator Sets Walk-Around Inspection
C27 and C32 Engines for Caterpillar Built Machines E539 High Intake Manifold Air Temperature
C32 Petroleum Engines Crankshaft Rear Seal - Remove
C32 Petroleum Engines Crankshaft Rear Seal - Install
TH48-E80 Oil/Gas Transmission Transmission Planetary - Assemble
TH48-E80 Oil/Gas Transmission Transmission Planetary - Disassemble
3500 Generator Sets Manual Stop Procedure
C32 Marine and Auxiliary Marine Engines Marine Transmission Oil Cooler - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Lockout Control - Remove