Transmission Hydraulic Control - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
A     | 138-7573     | 连杆支架     | 2     |
注: 为便于安装,在所有软管、所有软管组件、所有导线及所有管组件上做出识别标记。 插接好所有软管组件和所有管子组件。 这将有助于防止液体渗漏,并有助于防止污物进入系统。
注: 清洁度是一项重要的因素。 开始进行拆卸步骤之前,应彻底清洁部件外部。 这将有助于防止脏污进入内部机构。
注: 检查 O 形密封圈、密封垫和密封是否磨损或损坏。 必要时,更换部件。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 卸下盘 (1) 。 断开线束组件 (2) 。 卸下盘组件 (3) 。
Show/hide table
图 1 | g01186744 |
- 断开软管组件 (6) 。 卸下法兰 (7) ,断开线束组件 (8) 。
Show/hide table
图 2 | g01186757 |
Show/hide table
图 3 | g01186762 |
- 卸下螺栓 (5) 和阀组件 (4) 。 卸下管 (9) 。
注: 记录联轴节组件 (10) 上槽口的方位。
- 卸下螺栓 (11) 、盘组件 (12) 和管 (13) 。
Show/hide table
图 4 | g01187090 |
- 将工具 (A) 和适当的起吊设备连接在变速箱液压控制阀 (15) 上。 变速箱液压控制阀 (15) 的重量约为 70 kg (155 lb)。 卸下螺栓 (14) 和变速箱液压控制阀 (15) 。
Show/hide table
图 5 | g01187006 |
Caterpillar Information System:
3126B Generator Set Engine CID 0164 FMI 02 Injector Actuation Pressure signal erratic
C13 and C15 On-highway Engines ECM Memory - Test
C7 and C9 Marine Engines Engine Cranks but Will Not Start
G3500 Engines Model View Illustrations
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0700 - FMI 02
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0590 - FMI 12
C7 and C9 On-Highway Engines Engine Rating Parameters
2005/07/01 A Improved Gasket is Now Available {1151, 1162}
Supplemental Parts and Service Information for the C18 Marine Propulsion Engine {1901, 7470} Supplemental Parts and Service Information for the C18 Marine Propulsion Engine {1901, 7470}
2005/07/18 A Improved Gasket is Now Available {1151, 1162}
3126B Petroleum Engine Air Shutoff - Install
784C and 785C Off-Highway Truck/Tractors Match Tire Size - Dual Tire Configuration
TH48-E80 Oil/Gas Transmission Transmission Hydraulic Control - Install
Guidelines for Installation and Maintenance of Sea Water Heat Exchangers, Strainers, and Fuel Coolers{1379, 3319} Guidelines for Installation and Maintenance of Sea Water Heat Exchangers, Strainers, and Fuel Coolers{1379, 3319}
C32 Petroleum Engines Water Temperature Regulator - Remove and Install
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0702 - FMI 02
C18 Generator Sets Walk-Around Inspection
C27 and C32 Engines for Caterpillar Built Machines E539 High Intake Manifold Air Temperature
C32 Petroleum Engines Crankshaft Rear Seal - Remove
C32 Petroleum Engines Crankshaft Rear Seal - Install
TH48-E80 Oil/Gas Transmission Transmission Planetary - Assemble
TH48-E80 Oil/Gas Transmission Transmission Planetary - Disassemble
3500 Generator Sets Manual Stop Procedure
C32 Marine and Auxiliary Marine Engines Marine Transmission Oil Cooler - Remove and Install