C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Caterpillar


CID 0100 FMI 03

Usage:

C4.4 444
Conditions Which Generate This Code:

The Electronic Control Module (ECM) detects the following conditions:

  • The signal voltage from the engine oil pressure sensor is greater than 4.95 Volts DC for more than eight seconds.

  • The ECM has been powered for at least two seconds.

  • The engine is not running or the engine coolant temperature is greater than 38 °C (100 °F).

System Response:

The ECM will log the diagnostic code. If equipped, the warning lamp will come on. The ECM will set data for engine oil pressure to the default value.

Note: The engine oil pressure that is displayed on the electronic service tool is the default value for engine oil pressure. The default engine oil pressure is 600 kPa (87 psi). The electronic service tool will display "Voltage Above Normal" on the status screens.

None

This diagnostic code can be caused by an open circuit or a short to another power source.

Test Step 1. Perform the following diagnostic procedure: Engine Pressure Sensor Open or Short Circuit - Test

Results:

  • OK - STOP

Caterpillar Information System:

C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0041 FMI 04
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0041 FMI 03
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Refrigerant Condenser - Remove and Install
C4.4 and C6.6 Engines for Caterpillar Built Machines CID 1639 FMI 09
C15 On-Highway Engine Engine Valve Lash - Inspect/Adjust
C32 Petroleum Engines Aftercooler - Remove
C32 Marine and Auxiliary Marine Engines Auxiliary Water Pump - Install
C13 and C15 On-highway Engines Diagnostic Trouble Codes
C32 Marine Engines Auxiliary Water Pump - Assemble
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
3126B Generator Set Engine Sensors and Electrical Connectors
C32 Marine Engines Auxiliary Water Pump - Disassemble
Reuse and Salvage for Fuel Injection Pumps and Nozzles on 3044, 3046, 3064, and 3066 Engines {1251} Reuse and Salvage for Fuel Injection Pumps and Nozzles on 3044, 3046, 3064, and 3066 Engines {1251}
2005/08/22 Troubleshooting Column-Type Fuel Level Senders {5574, 7481}
3126B Petroleum Engine Electronic Control Module - Remove and Install
C13 and C15 On-highway Engines Fuel Temperature Is High
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0100 FMI 04
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Mode Selection Circuit - Test
C18 Petroleum Generator Sets Engine Warm-up
C32 Petroleum Engines Aftercooler - Install
3126B Petroleum Engine Air Shutoff - Remove
C15 Generator Sets Model View Illustrations
C18 Generator Sets Plate Locations and Film Locations
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Refrigerant Compressor - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.