Accessory Drive - Remove and Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove allen head bolt (1) from accessory drive housing (8). Remove allen head bolts (6) from accessory drive housing (8).
- Remove accessory drive housing (8) from the front housing.
- If necessary, follow Steps 3.a through 3.c in order to disassemble the accessory drive.
- Remove retaining ring (2) from accessory drive housing (8).
- Place accessory drive housing (8) onto a suitable support. Press the assembly of gear (4) and bearings (3) and (5) out of accessory drive housing (8). Use a suitable puller in order to remove bearings (3) and (5) from gear (4).
- Remove O-ring seal (7) from accessory drive housing (8).
Show/hide table
Illustration 1 | g01212859 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 7M-7456 | Bearing Mount Compound | 1 |
B | 207-1601 | Rubber Lubricant | 1 |
C | 9S-3263 | Thread Lock Compound | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- If necessary, follow Steps 1.a through 1.e in order to assemble the accessory drive.
- Inspect the condition of the teeth and the splines of gear (4) for wear or damage. Inspect bearings (3) and (5), retaining ring (2), and the front housing for wear or damage. Replace any components that are worn or damaged.
- Apply a small continuous bead of Tooling (A) to the inner surface (X) of bearing (5). Place the gear shaft on a suitable support. Press on the inner race of bearing (5) until bearing (5) is against the shoulder of gear (4). Remove any excess sealant.
- Apply a small continuous bead of Tooling (A) to inner surface (Z) of bearing (3). Place the front face of the inner race of bearing (3) onto a suitable support. Press the shaft of gear (4) into bearing (3) until the shoulder of the gear is against the bearing. Remove any excess sealant.
- Apply a small continuous bead of Tooling (A) to the outer surface (Y) of bearing (5). Place accessory drive housing (8) on a suitable support. Press the assembly of gear (4) and bearings (3) and (5) into accessory drive housing (8). Ensure that bearing (5) is against the front face of the recess in accessory drive housing (8). Remove any excess sealant.
- Install retaining ring (2) into the groove in accessory drive housing (8). Ensure that retaining ring (2) is correctly positioned in the groove.
- Lightly lubricate a new O-ring seal (7) with Tooling (B) and install O-ring seal (7) into the groove in accessory drive housing (8).
- Inspect the bore in the front housing (not shown) for damage. If necessary, replace the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" and Disassembly and Assembly, "Housing (Front) - Install".
- Lightly lubricate bearing (3), bearing (5), and gear (4) with clean engine lubricating oil. Install the assembly of the accessory drive to the front housing.
- Apply Tooling (C) to allen head bolts (1) and (6). Install allen head bolts (6) to accessory drive housing (8). Install allen head bolt (1) to accessory drive housing (8).
- Tighten bolts (1) and (6) to a torque of
22 N·m (16 lb ft) . - Ensure that there is backlash between the idler gear and the accessory drive gear.
Show/hide table
Illustration 2 | g01193304 |
Caterpillar Information System:
Caterpillar 270 Air Compressor Air Compressor Leaks Oil
Caterpillar 270 Air Compressor Air Compressor Leaks Coolant
C7.1 Engines for Caterpillar Built Machines Exhaust Manifold
C7.1 Engines for Caterpillar Built Machines Flywheel
C6.6 Industrial Engine Fuel Priming Pump
C6.6 Engines for Caterpillar Built Machines Fuel Injection Lines
C6.6 Industrial Engine Fuel Transfer Pump
C9 Generator Set Fuel System - Prime
C15 and C18 Petroleum Generator Sets After Starting Engine
3512C and 3516C Marine Auxiliary and Generator Set Engines Before Starting Engine
Caterpillar 270 Air Compressor Air Compressor is Noisy
Caterpillar 270 Air Compressor Air Compressor Cycles Constantly
C15 On-Highway Engine Electronic Unit Injector - Adjust
C32 Marine and Auxiliary Marine Engines Engine Oil Filter Base - Remove
C7.1 Engines for Caterpillar Built Machines Front Housing and Covers
C9 Generator Set Engine Crankcase Breather - Clean
C7.1 (Mech) Industrial Engine Oil Pump
Caterpillar 270 Air Compressor Excessive Build-Up and Recover Time
Caterpillar 270 Air Compressor Excessive Oil at Exhaust Ports or Air Strainer
Caterpillar 270 Air Compressor Air Compressor Governor - Test and Adjust
Caterpillar 270 Air Compressor Discharge Valve Leakage - Test
C7.1 (Mech) Industrial Engine Gear Group (Front)
3126B Petroleum Engine Water Temperature Regulator Housing - Remove and Install
C18 Petroleum Generator Sets Generator Lead Connections