301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Caterpillar


Track - Remove and Install

Usage:

301.6C JBB

Removal Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     138-7574     Link Bracket     2    
B     189-0409     Shackle As     2    
C     180-3034     Repair Stand Set     1    

  1. Raise the boom until the boom cylinder is fully extended. Fully extend the stick cylinder and the bucket cylinder.



    Illustration 1g01176217

  1. Attach Tooling (A), Tooling (B), and a suitable lifting device to the machine. The weight of the machine is approximately 1695 kg (3737 lb).



    Illustration 2g01176161

  1. Position the machine on Tooling (C) and suitable blocking so that the bottom of the track is approximately 254 mm (10.0 inch) from the ground.

  1. Position the bucket on suitable blocking.



    Illustration 3g01176170

  1. Release the track tension at fitting (1). Refer to Operation and Maintenance, "Track Adjustment - Adjust".



    Illustration 4g01176190

  1. Attach a suitable lifting device in order to support track (2). The weight of track (2) is approximately 77 kg (170 lb).



    Illustration 5g01176246

  1. Position the front of track (2) on the ground.



    Illustration 6g01176259

  1. Attach a suitable lifting device to track (2). The weight of track (2) is approximately 77 kg (170 lb).

  1. Remove track (2) .

Installation Procedure

Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     138-7574     Link Bracket     2    
B     189-0409     Shackle As     2    



    Illustration 7g01176259

  1. Attach a suitable lifting device to track (2). The weight of track (2) is approximately 77 kg (170 lb).

  1. Position track (2) on the sprocket.



    Illustration 8g01176246



    Illustration 9g01176190

  1. Attach a suitable lifting device in order to support track (2). The weight of track (2) is approximately 77 kg (170 lb).

  1. Install track (2) .



    Illustration 10g01176170

  1. Adjust the track tension at fitting (1). Refer to Operation and Maintenance, "Track Adjustment - Adjust".



    Illustration 11g01176217

  1. Attach Tooling (A), Tooling (B), and a suitable lifting device to the machine. The weight of the machine is approximately 1695 kg (3737 lb). Position the machine on the ground.

Caterpillar Information System:

325C LCR Excavator Machine Systems Stick - Install
325C LCR Excavator Machine Systems Stick - Remove
C15 and C18 Petroleum Generator Sets Engine Oil and Filter - Change
302.5C Mini Hydraulic Excavator Engine Supplement Fuel Filter and Water Separator Base - Remove and Install
2006/03/27 The Reliability and Durability of the Electric Starting Motor Is Increased {1408, 1417, 1453, 7499}
2005/06/27 Improved Engine Oil Coolers are Now Used {1378}
Pin Grabber Quick Coupler Spring (Blocking Bar) - Replace
M318C and M322C Wheeled Excavators Power Train Differential - Assemble - Rear
M318C and M322C Wheeled Excavators Power Train Differential - Disassemble - Rear
345B Series II Excavator Hydraulic System (Ecomate Attachment) Bucket Hydraulic System
302.5C Mini Hydraulic Excavator Engine Supplement Engine - Install
345C MHPU Mobile Hydraulic Power Unit Machine Systems Gear Pump (Pilot) - Install
302.5C Mini Hydraulic Excavator Engine Supplement Refrigerant Compressor - Remove and Install
302.5C Mini Hydraulic Excavator Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
385C Excavator and 385C MHPU Mobile Hydraulic Power Unitwith UHD Attachment Demolition Boom Removal
302.5C Mini Hydraulic Excavator Engine Supplement Fuel Transfer Pump - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Swivel - Remove
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Seat - Remove and Install
302.5C Mini Hydraulic Excavator Machine Systems Swivel - Disassemble
302.5C Mini Hydraulic Excavator Machine Systems Swivel - Assemble
302.5C Mini Hydraulic Excavator Engine Supplement Refrigerant Condenser - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Selector Valve (Alternate Pattern Control) - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Final Drive and Travel Motor - Disassemble
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.