Gear Pump (Pilot) - Assemble
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install bushings (24), balls (23), and seal (22) onto flange (25) .
Show/hide table
 | |
| Illustration 1 | g01171919 |
- Install seal (21) onto plate (19) .
Show/hide table
 | |
| Illustration 2 | g01171943 |
- Install bushing (20), and plate (19) into body (13) .
Show/hide table
 | |
| Illustration 3 | g01171918 |
- Install seal (18) onto plate (15) .
Show/hide table
 | |
| Illustration 4 | g01171942 |
- Install gear (17), gear (16), and plate (15) in body (13) .
Show/hide table
 | |
| Illustration 5 | g01171917 |
- Install seal (14) onto plate (12) .
Show/hide table
 | |
| Illustration 6 | g01171941 |
- Install body (13) and plate (12) .
Show/hide table
 | |
| Illustration 7 | g01171916 |
- Install seal (9), balls (10), and gears (11) .
Show/hide table
 | |
| Illustration 8 | g01171915 |
- Install seal (8) onto plate (7) .
Show/hide table
 | |
| Illustration 9 | g01171914 |
- Install plate (7) into manifold (6) .
Show/hide table
 | |
| Illustration 10 | g01171913 |
- Install manifold (6) and bolts (5) .
Show/hide table
 | |
| Illustration 11 | g01171912 |
- Install sleeve (4) in gear pump (2) .
Show/hide table
 | |
| Illustration 12 | g01171911 |
- Install gear pump (2) onto piston pump (3) and install bolts (1) .
Show/hide table
 | |
| Illustration 13 | g01171910 |
End By: Install the main hydraulic pump and gear pump. Refer to Disassembly and Assembly, "Main Hydraulic and Gear Pump (Pilot) - Install".
Caterpillar Information System:
302.5C Mini Hydraulic Excavator Machine Systems Gear Pump (Pilot) - Disassemble
Supplemental Product Support Literature for a Factory Installed 20 kW Right Front Corner Mounted Generator Set ( 247-5442 Hydraulic Generator Arrangement) and the Operation Instructions {1404, 1408, 4450, 5057, 5070, 7000} Supplemental Product Support Literature for a Factory Installed 20 kW Right Front Corner Mounted Generator Set ( 247-5442 Hydraulic Generator Arrangement) and the Operation Instructions {1404, 1408, 4450, 5057, 5070, 7000}
302.5C Mini Hydraulic Excavator Machine Systems Pilot Valve (Joystick) - Assemble
302.5C Mini Hydraulic Excavator Machine Systems Pilot Valve (Joystick) - Disassemble
301.6C, 301.8C and 302.5C Mini Hydraulic Excavators Swing Frame and Cylinder Bearings - Lubricate
325D and 329D Excavators Hydraulic System Swivel
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Pilot Valve (Joystick) - Install
301.6C, 301.8C and 302.5C Mini Hydraulic Excavators Tip-Over Protective Structure (TOPS) - Inspect
M318C and M322C Excavators Engine Supplement Electric Starting Motor - Remove and Install
M325D MH Material Handler Cab Door
M325D MH Material Handler Storage and Literature Compartment
M325D MH Material Handler Monitoring System
302.5C Mini Hydraulic Excavator Machine Systems Main Hydraulic Pump - Disassemble
302.5C Mini Hydraulic Excavator Machine Systems Main Hydraulic Pump - Assemble
330D and 336D Excavators Specifications
320D Excavator Fuses - Replace
330D and 336D Excavators Boom/Stick/Bucket Combinations
S320B, S325B, S340B, S365B and S385B Demolition and Scrap Shears Bushings - Lubricate
M318C and M322C Excavators Machine Systems Swivel - Remove
M318C and M322C Excavators Machine Systems Swivel - Install
330D and 336D Excavators Plate Locations and Film Locations
M318C and M322C Excavators Machine Systems Swing Drive - Remove
M318C and M322C Excavators Machine Systems Swing Drive - Install
330D and 336D Excavators Alternate Exit